Tractors and Farm Equipment
Timing and Firing Orders

How do you set timing for a mack injector pump?

Top Answer
User Avatar
Wiki User
Answered 2011-09-12 21:58:08

first of all ,you will need an A/B light ,you can purchase one from kent Moore tools ,then you will bar the engine over until you see the 1 and 6 six marks on the fly wheel at the bottom of the bell housing . If you have and older e6 model there will be apionter at the harmonic balancer at the front of the engine ,bar the engine until both indictor lights come on on the a/b light then you be able to see what the timing is set at

User Avatar

Your Answer


Still Have Questions?

Related Questions

How do you set injector pump timing on Mazda t3500?

how to set engine timing for mazda t3500

How do you set injector pump timing on Nissan cabstar?

how do you set injector pump timing for a Nissan cab star? provide a diagram.

How do you set the injector pump timing on a Kubota B6000?

Injector timing on b6000 is adjusted by adding or subtracting shims under the injector pump. Timing should be set with fly wheel timing mark on cyclinder #1

How do you set the injector pump timing on a 4HF1 Isuzu engine?

You can set the injector pump timing on a 4HF1 Isuzu engine by adjusting the fuel injection screw. The adjusting screw will restrict the amount of fuel to be injected.

How can you set diesel engine timing?

If you are referring to ignition timing, diesel ignition timing is primarily controlled by the injector timing. This is also why diesel engines run such high injector pressures. The timing is very carefully controlled by the vehicles computer.

How do you set the timing on a 1990 Cavalier after changing the water pump?

the water pump is located next to the throttle body. there is no reason to set the timing.

Do you need to set the timing of the oil pump when you change the timing belt?


How do you set the timing on a 2002 ford courier van 1.8 diesel?

There is no ignition timing to set on a diesel. If you have somehow disturbed the injector timing you'll have to take it to a dealer, as setting that requires special equipment.

How do you remove the water pump on a 1987 Toyota Camry?

The timing belt has to be removed to access the water pump. Once the pump is replaced the timing belt has to be replaced and set.

How do you replace the water pump on a 1997 Plymouth Voyager 3.0L?

water pump on this 3.0 is driven with the timing belt. it is internal water pump you will have to set your timing before you start replace your timing belt if it is worn out.

Where is the water pump located on a Honda Civic DX?

The water pump is located in the timing set up behind the timing cover its a good idea to replace the timing belt when u replace the water pump

How do you time an isuzu 4hf1?

how many degrees do you set an injector pump of 4hf1 isuzu truck

What is wrong with a truck that is backfiring?

If it is petrol then it is probably the ignition timing not set correctly. If it is diesel then it is probably the injection pump timing not set correctly

How do you adjust the injector pump timing for an Oldsmobile 5.7 V8 diesel?

the timing on the 5.7s isn't critical. there is a line in both the pump and the atatchment plate. if the heads have been shaved you will find that if you line those 2 marks up it will be hard to start, blow white smoke on startup, and knock. move the pump to the right 60 thou if your standing in front of the motor, and u will find it will start and run better. hope that helps Well i had anpontiac bonniville with a 5.7 d for ten years and 5 injector pump rebuilds and 2 engines later i can tell you lots of things as one of my friends used to work on them the injectore pump has timing lines set from the factory but over time or rebuid there not always accurate Oldsmobile came out with a cylider timing lite which you could reset the timing as the lines may nit be accurate but to find a mechanic or garage that still has the tool might be difficult to find sice olds brand no longer in existence and engines very rare now but be wary as it s the only true way to set your timing had to have mine redone evey 2 to 3 years as internal wear would take it out of timing {injector pump ]

How do you timing up injector pump on 4D32 diesel with timng front covers on?

I have the manual on the 4D32 engine. There are two sets of timing marks on the 4D32 engine. One set is marked 1-4 these are used on the bottom of the crank, the other is marked 2-3 and these are used on the top of the crank. The easiest way to time the engine is to remove the valve cover and turn the engine to the 0 degree. It was easier for me to use the bottom timing marks. When on 0 degree, at top dead center, both valves wil be closed. If you can not move the lifters, rotate the engine one revolution and stop on 0 degree. You should be able to move the lifters. Now find the notched gear tooth on the injector pump. One tooth has the back edge cut on the the gear. There is a mark on the injector housing, at about 2 o"clock. Turn the notched tooth to the mark and start pushing the pump into place. As the pump gears engage the timing mark on the pump will move down the distance on one tooth. Bolt pump into place and timing should be correct.

Where is the water pump located on a 1997 Honda Passport?

The pump is set into the front of the engine block. You have to remove the timing belt to get to it.

How do you set the timing on a 96 4 cylinder ford ranger when replacing the timing belt Is it nec. to remove the power steering pump pully then the pump in order to remove the bracket.?

Yes the pulley has to be removed, To time this disconnect the spot plug(disables the computer) and set timing to factory spec's

Does replacing water pump have anything to do with a timing change on a 1997 Oldsmobile lss?

It depends on the motor..if you have overhead cam...then YES. The timing belt has to be removed when the water pump is changed and the cam sprockets have to be set to correct timing when the belt is replaced.

How do you set the timing on a 1979 camaro that has no pointer?

If you look stright down between the water pump and engine block you will see the timing mark.

How do you set timing on a 95 Caprice?

You dont. It is an LT1 engine and the distributor is behind the water pump.

How do you turn the injection pump up on a jd 4010?

To turn the injection pump up you set it to TDC static timing by rotating the pump. It is adjusted by an Allen screw on the lower side of the pump.

Are a water pump and a timing belt on a 1996 geo tracker somehow?

HI, There are definitely a timing belt and a water pump on the engine. The timing belt is behind the cover that is on the front of the engine and when there you will also find the timing belt tensioner, they come as a set when you purchase them. The water pump is also at the front of the engine and sits at the left of the timing belt cover as you look at the engine, the pump is driven by the belt, you can't miss it. Happy repairing and good luck.Steve H.

How do I adjust diesel timing on a 1992 Ford F-350?

clean on the front of the pump on top where it bolts on the motor there are timing marks there line up the long marks to set the timing.

94 Chrysler lebaron set timing and replaced water pump and now it wont start why?

did you make sure the #1 piston was top dead center and that when you set your timing that the springs where without tension? if not its out of time

How do you set fuel pump timing for TD27 engine?

This can be done through your settings. It is best to have a professional look through it and do it for you.