Auto Parts and Repairs
Acura Integra

How do you slow the idle speed on a 1992 Acura Integra?

363738

Top Answer
User Avatar
Wiki User
2006-04-10 06:45:24
2006-04-10 06:45:24

As you face the opening to the throttle body air intake, look to the left and you'll see a slotted brass adjustment screw (may be covered up by sealant). Turn clockwise to decrease idle speed. -- Ian

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The 1991 Acura Integra idle air control valve can be found on the firewall. The valve will be on the drivers side of the firewall.

User Avatar

To fix this: 1. Loosen the distributor and adv timing by turning it counter-clockwise. and/or 2. Locate idle screw (brass, slotted) next to air intake throttle body and back it out till idle speed increases.

User Avatar

On a 1992 Acura Vigor idle is adjusted through a idle control valve. Tightening the valve well raise the lower the idle and loosening it will raise it.

User Avatar

Check idle adjustment (rpm) then check timing, then check for misfire-start there.

User Avatar

Idle speed is computer controlled and is not adjustable. If the speed is incorrect check for a stuck idle speed air motor, on the throttle body, and for air flow problems.

User Avatar

You need to replace your IAC Valve (Idle Air Control Valve) It's located in the back of Your Intake Manifold.

User Avatar

The idle on all fuel injected engines is controlled by the engine control module. There are no adjustments to be made. If your idle is high it could be caused by a vacuum leak or a sticking or bad idle air control motor. If you have a check engine light on then you will need to have it scanned for codes.

User Avatar

the cold idle is controlled by the PCM ( power train control module) the computer of the car and idle is not adjustable.

User Avatar

Idle speed is computer controlled and is not adjustable.Idle speed is computer controlled and is not adjustable.

User Avatar

Idle speed is PCM controlled and is not adjustable.Idle speed is PCM controlled and is not adjustable.

User Avatar

Idle speed is computer controlled and is not adjustable.Idle speed is computer controlled and is not adjustable.

User Avatar

There is not an "IDLE" sensor.The engine computer sets and adjusts the idle speed.If the idle speed won't settle down you need to have the computer scanned to determine the causeBUTVery often with this problem the throttle body is dirty and just needs cleaning.

User Avatar

Does not have one. Idle speed is controlled electronically through an idle speed control module.

User Avatar

If it has EFI (Electronic Fuel Injection) there is no idle speed adjustment. The idle speed is adjusted electronically.

User Avatar

You don't. The idle speed is determined by the on board computer and the idle speed control (ISC).

User Avatar

First you must check the ISC motor ( idle speed control) operation. Its located by the throttle body. It controls idle and high idle speeds. Good luck

User Avatar

warm up speed of turbine,andthe minimum speed of turbine before loading is called idle speed.

User Avatar

Idle speed is not adjustable on this car.

User Avatar

Idle speed is computer controlled and is not adjustable.

User Avatar

The idle speed on a VW Polo is regulated by a Idle air control valve. The valve is located in the engine bay and can be adjusted through to either increase and lower the idle speed.

User Avatar

Idle is computer controlled and is not adjustable. If idle speed is incorrect, you have a sensor or actuator issue.Idle is computer controlled and is not adjustable. If idle speed is incorrect, you have a sensor or actuator issue.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.