Chevy Celebrity
Radio

How do you take off the face plate that shuts in your radio on a 89 Celebrity?

202122

Top Answer
User Avatar
Wiki User
Answered
2005-11-06 05:59:13
2005-11-06 05:59:13

If it's like my 85 celebrity the radio is held in by 3 screws. These screws are located on either side of the radio and you've got to take the piece of dashboard plastic off to gain access. This piece of plastic dashboard trimming runs all the way across the dash and includes the vent louvers. It took me several hours to find all of the attachment pieces under the dash. Some are clip-in and some are cheap metal nuts screwed on to studs of the dashboard piece. It was such a pain to remove for me, I just left it off and use styrofoam cups to direct the vent air. But then again, I'm sort of lazy. Good luck.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


If you mean reset button there is none. If you mean radio presets then they are right there on the radio face plate. They are numbered and easy to see.

by bying one !!!!!!!//////////if it is a replacement radio go to the place that sold it to you or a junk yard

Most stock radio just unscrew out when you pop off the panel there should be 2-4 bolts depending on the size of the radio

It's possible but it's not easy to find another one.

To remove the radio from the 1990 Lexus ES250, first pry the face plate from the dashboard. Then remove the clips that hold each side of the radio. Then, remove the wires to release the radio.

The Subaru Forester has a radio that must be removed with an Allan Wrench. The face plate is removed with the Allan Wrench and the mounting screws can then be accessed.;

Well sometimes the radio is hooked up to the ignition itself. It is just the ignition wire, if it has a disconnecting face plate then you can turn it off by taking the face plate off. Or if you would like, you can pull the radio out and disconnect the wire from the ignition and it will not still be on when you cut the truck off.

you have to remove the pastic face plate that surrounds the radio unit, (few screws) once done remove the face plate, and should have 2 bolts holding the radio in undo those and pull out radio then disconnect wires accrodingly

remove the four face plate screws and remove the face plate. Then slide the special removal tools in each side of the radio and it will slide right out, or if you are like me and don't have the special tools, bust it up and take it out in pieces AAAGGGGGGGGG Thats what i did was destroy that stock radio and rip it out like the Mayans used to do with hearts... it was AWESOME!!

Face for the Radio was created on 2007-06-25.

Face Plate is used on Lathe machine. It is just like lathe chuck. irregular shape job clamp on face plate by clamps, bolts.

You need to gently pry off the console molding using a flat head screw driver. Start at the top, gently remove that. Then, you'll see the radio exposed, there are some screws around the radio which you can unscrew and pull out the radio unit which is big and chunky, you'll have to unplug the speaker wire from the radio to remove it entirely. To replace, I bought a face plate kit from Wal Mart, along with the new stereo unit and a speaker wire adapter plug. Match up the wires from the adapter to the new stereo's wires (the wire adapter should have a diagram and the wires should themselves be labled: L speaker, R speaker, L Rear Speaker,..etc. Now, making the face plate fit and screwing it back into the dash takes some doing. I had to drill a couple of holes in the original bracket which I took off of the Geo Radio and put around the new radio with the face plate. The new radio will be much smaller than the old Geo Delco radio so you have to make it look good by adding the face plate, then attaching the speaker wire plug on the geo to the new radio with spliced wire connection, then screw in the radio, then fit the center console cover back over the whole thing. This last part required a bit of pushing and pressure to make the console face plate go back on over the new radio but it should work out. Sounds complicated I know but it'll work.

Replacing a car stereo is not a difficult process. All you need to do is take off the face plate, unscrew the radio, and unhook the wires. Then place the new stereo in, hook up the wires, screw the new stereo in, and replace the face plate.

Pull knobs off for air and fan control. Remove 2 screws. Gently work cover off. To remove radio: remove 4 screws then pull radio straight out. Unclip radio wiring harness and antenna wire.

Depending on wich Saturn its really easy just pop off the dash around the radio remove the screws take out your radio unplug the wires and buy a new radio w/ wiring harness and face plate.

a radio poops in your face

remove the face plate and get a safety pin or use the tip of a pen or pencil and press the reset button

1st you would need to know if the car is a 93 convertable or sports sedan. If the sports sedan, when you say radio...do you mean the face plate on the dash that you see..this is the ICM...the radio component or the ecm is in the dash...

i think its your face shape. look at a celebrity who has the same face shape as you

lady gaga sings that song poker face on the radio

First pull out the ash tray, this is where you find the first set of screws to remove the face plate. I can't remember more because it's been a while since i did mine, but this should be enough to get started. After you can pop off the face plate, there will be i believe 4 screws holding the radio in its position, use a long screwdriver so you don't hurt your hand.

youll most likely have to replace the whole radio. from what ive been told it would cost the same or more just for the faceplate alone.

FNL's Celebrity Beauty Secrets - 2013 Celebrity Beauty Secrets How to Get the Perfect Summer Face 1-6 was released on: USA: 15 July 2013

You have to gentle take the face plate off the front part of your dash. The face plate goes around the radio and the air conditioning controls. There are about 6 clips one on top 2 on each sides and one on the bottom. A flat head screw driver works well. Once you pop that off disconnect traction control, (4x4), and hazards from back of panel. Then there will be some screws holding the radio in take those out and the system should just slide out.

A removable face plate helps to deter theft if removed upon exiting the car.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.