answersLogoWhite

0


Best Answer
Copy

Depending on the vehicle, you would use a wrench SAE or Metric, to turn the nut down with to tighten. You may want to go to a car parts store, and get a repair manual for your car. They cost about $16.00 Or, go to a Public Library.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:15:11
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Add your answer:

Earn +5 pts
Q: How do you tighten the positive battery cable to the solenoid or starter?
Write your answer...
Submit

Related Questions

Why is 1994 Isuzu Rodeo starter clicking. The starter solenoid clicks then the starter motor engages. HAYNES quotes problem is battery or starter solenoid contacts or starter motor connections.Ideas?

either clean and tighten cable connections or get battery tested. if not the battery, it is the solenoid or the starter If it is clicking and not starting at first, but starts after a few tries, its your starter taking a dump. Replace it.


How do you install a starter on a 1997 Toyota Corolla 1.8L?

Remove the positive battery cable from your 1997 Toyota Corolla battery. Tighten the starter with the retaining bolts. Attach the cables to the front of the starter. Reattach the positive cable to the battery.


How do you change a starter on a 2005 Dodge Dakota?

# Disconnect and isolate negative battery cable. # Raise and support vehicle. # Note: If equipped with 4WD and certain transmissions, a support bracket is used between front axle and side of transmission. Remove 2 support bracket bolts at transmission. Pry support bracket slightly to gain access to lower starter mounting bolt. # Remove one bolt and one nut if equipped with a manual transmission. # Move starter motor towards front of vehicle far enough for nose of starter pinion housing to clear housing. Always support starter motor during this process, do not let starter motor hang from wire harness. # Tilt nose downwards and lower starter motor far enough to access and remove nut that secures battery positive cable wire harness connector eyelet to solenoid battery terminal stud. Do not let starter motor hang from wire harness. # Remove battery positive cable wire harness connector eyelet from solenoid battery terminal stud. # Disconnect battery positive cable wire harness connector from solenoid terminal connector receptacle. # Remove starter motor.# Disconnect and isolate negative battery cable. # Raise and support vehicle. # Note: If equipped with 4WD and certain transmissions, a support bracket is used between front axle and side of transmission. Remove 2 support bracket bolts at transmission. Pry support bracket slightly to gain access to lower starter mounting bolt. # Remove two bolts if equipped with an automatic transmission. # Move starter motor towards front of vehicle far enough for nose of starter pinion housing to clear housing. Always support starter motor during this process, do not let starter motor hang from wire harness. # Tilt nose downwards and lower starter motor far enough to access and remove nut that secures battery positive cable wire harness connector eyelet to solenoid battery terminal stud. Do not let starter motor hang from wire harness. # Remove battery positive cable wire harness connector eyelet from solenoid battery terminal stud. # Disconnect battery positive cable wire harness connector from solenoid terminal connector receptacle. # Remove starter motor.# Connect solenoid wire to starter motor (snaps on). # Position battery cable to solenoid stud. Install and tighten battery cable eyelet nut . Do not allow starter motor to hang from wire harness. # Position starter motor to transmission. # Install and tighten lockwasher nut and bolt . # Lower vehicle. # Connect negative battery cable.# Connect solenoid wire to starter motor (snaps on). # Position battery cable to solenoid stud. Install and tighten battery cable eyelet nut . Do not allow starter motor to hang from wire harness. # Position starter motor (4) to transmission. # If equipped with automatic transmission, slide cooler tube bracket into position. # Install and tighten both bolts . # Lower vehicle. # Connect negative battery cable.


How do you replace the starter on a Jeep Cherokee 98?

# Disconnect and isolate the battery negative cable. # Raise and support the vehicle. # Disconnect the battery cable and solenoid feed wire from the starter solenoid # Remove the two starter mounting screws, the starter motor, and any starter motor shims # Reverse the removal procedures to install. Tighten the starter hardware as follows: #* Mounting screws - 45 N·m (33 ft. lbs.) #* Solenoid battery cable nut - 10 N·m (90 in. lbs.) #* Solenoid terminal nut - 6 N·m (55 in. lbs.) == # Disconnect and isolate the battery negative cable. # Raise and support the vehicle. # Disconnect the battery cable and solenoid feed wire from the starter solenoid # Remove the lower starter mounting screw. # Remove the upper starter mounting screw and the starter motor. # Reverse the removal procedures to install. Tighten the starter hardware as follows: #* Upper mounting screw (rear screw) - 55 N·m (40 ft. lbs.) #* Lower mounting screw (front screw) - 41 N·m (30 ft. lbs.) #* Solenoid battery cable nut - 10 N·m (90 in. lbs.) #* Solenoid terminal nut - 6 N·m (55 in. lbs.)


Where is the starter located on a 2001 expedition xlt?

Follow the BIG RED positive wire from the battery strait to the starter. It should be in the Passengers Side between the engine and transmission. Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.


How do change the starter on a 2000 Dodge Durango?

== # Disconnect and isolate the battery negative cable. # Raise and support the vehicle. # Remove the nut and the lock washer that secures the lower mounting flange of the starter motor to the stud on the automatic transmission torque converter housing # While supporting the starter motor with one hand, use the other hand to remove the screw and washer that secures the upper mounting flange of the starter motor to the automatic transmission torque converter housing. # Slide the automatic transmission cooler tube bracket forward on the tubes far enough for the starter motor mounting flange to be removed from the lower mounting stud. # Lower the starter motor from the front of the automatic transmission torque converter housing far enough to access and remove the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the battery positive cable eyelet terminal from the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Disconnect the battery positive cable solenoid terminal wire harness connector from the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the starter motor from the automatic transmission torque converter housing. == # Disconnect and isolate the battery negative cable. # Raise and support the vehicle. # Remove the screw and washer (rearward facing) that secures the lower mounting flange of the starter motor to the automatic transmission torque converter housing # While supporting the starter motor with one hand, use the other hand to remove the screw and washer (rearward facing) that secures the upper mounting flange of the starter motor to the automatic transmission torque converter housing. # Lower the starter motor from the front of the automatic transmission torque converter housing far enough to access and remove the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the battery positive cable eyelet terminal from the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Disconnect the battery positive cable solenoid terminal wire harness connector from the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Remove the starter motor from the automatic transmission torque converter housing. == == # Position the starter motor to the automatic transmission torque converter housing. # Reconnect the battery positive cable solenoid terminal wire harness connector to the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install the battery positive cable eyelet terminal onto the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install and tighten the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Tighten the nut to 13.6 N·m (120 in. lbs.) Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Position the hole in the starter motor lower mounting flange over the stud on the automatic transmission torque converter housing. # Slide the automatic transmission cooler tube bracket rearward on the tubes and into position over the starter motor upper mounting flange. # Loosely install the screw and washer unit that secures the starter motor upper mounting flange to the automatic transmission torque converter housing. # Loosely install the lock washer and nut that secures the starter motor lower mounting flange to the stud on the automatic transmission torque converter housing. # Tighten the screw and washer unit and the nut that secure the starter motor mounting flange to the automatic transmission torque converter housing. Tighten the screw and the nut to 67.8 N·m (50 ft. lbs.) # Lower the vehicle. # Reconnect the battery negative cable. == # Position the starter motor to the automatic transmission torque converter housing. # Reconnect the battery positive cable solenoid terminal wire harness connector to the connector receptacle on the starter solenoid. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install the battery positive cable eyelet terminal onto the solenoid B(+) terminal stud. Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Install and tighten the nut that secures the battery positive cable eyelet terminal to the starter solenoid B(+) terminal stud. Tighten the nut to 13.6 N·m (120 in. lbs.) Always support the starter motor during this process. Do not let the starter motor hang from the wire harness. # Position the starter motor mounting flange on the automatic transmission torque converter housing and loosely install the two screw and washer units to secure it. # Tighten the two screw and washer units that secure the starter motor mounting flange to the automatic transmission torque converter housing. Tighten the screws to 67.8 N·m (50 ft. lbs.) # Lower the vehicle. # Reconnect the battery negative cable.


How do you wire a starter solenoid on a 1999 Mercury Sable 3.0?

StarterRemoval & Installation1. Disconnect the negative battery cable.2. Raise and safely support the vehicle.3. Remove the starter terminal cover.4. Remove the terminal nut and separate the battery starter cable from the starter motor.5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.6. Remove the starter motor retaining bolts.7. Remove the starter motor from the vehicle.To Install:8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.11. Install the starter solenoid safety cap. If equipped.12. Lower the vehicle.13. Connect the negative battery cable.14. Start the engine several times to check starter motor operation.


When starting car what if it just clicks?

That means the solenoid IS working, but power is too low to turn the starter. Check and if necessary clean or tighten the battery terminals. If still the same, charge your battery on slow for at least 12 hours, or get another battery.


1999 Chrysler Town and Country starter installation?

To install the starter, hold the starter motor spacer in position, install the starter motor-to-transaxle bell housing bolts, tighten it, and engage the solenoid wiring connector onto the terminal. Then, connect the B+ wire, tighten the retaining nut, lower the vehicle, connect the negative battery cable and verify starter motor operation. ÊÊ


How do you change the starter on a 2000 Dodge Neon?

The starter is located under the car where the transmission and engine meet toward the front of the neon. The starter actually bolts up with face toward the transmission. You must get the car up on ramps or on a hoist to see the starter. This is just a general method; it is very hard to give words to describe some of the steps without pictures. Removal: Disconnect and isolate the battery negative cable. Raise vehicle on hoist. Remove starter bolts. Remove starter assembly. Disengage latch and remove solenoid connector from starter assembly. Remove battery positive connector from starter assembly. It is not necessary to remove the alternator output lead from the connector. Installation: Clean corrosion/dirt from the cable and wire terminals before installing wiring to the solenoid. Attach battery positive connector to starter. Ensure alternator output connector is snapped into the battery positive connector. Tighten the captive nut to 10 Nm (90 in. lbs.) . CAUTION: It is critical that the alternator output terminal be connected to the battery positive terminal of the starter solenoid, for proper operation of the charging and cranking systems. Install solenoid connector to starter. Ensure that latch is fully engaged. Position the starter face into transmission housing. Start bottom mounting bolt and thread in until bolt is snug. Attach ground cable to upper starter mounting bolt. Ensure the proper starter alignment before tightening the starter mounting bolts to 54 Nm (40 ft. lbs.) torque. Lower vehicle and connect negative battery cable.


How do you replace the starter in a 1996 Dodge Ram?

== # Disconnect and isolate the battery negative cable. # Raise and support the vehicle. # Remove the nuts from the terminal studs for the starter battery lead and solenoid lead # Remove the hardware securing the starter to the bellhousing # Move the starter forward to clear the lower mounting stud (V-6/V-8 engine) and for the starter gear housing nose to clear the bellhousing. This allows the starter to come down past the exhaust pipe # Reverse the removal procedures to install. Tighten the starter hardware as follows: #* Starter mounting bolts to 68 N·m (50 ft. lbs.) #* Starter mounting nut - 27 N·m (20 ft. lbs.) #* Battery lead terminal nut - 14 N·m (120 in. lbs.) #* Solenoid lead terminal nut - 2.5 N·m (22 in. lbs.) == # Disconnect and isolate both of the battery negative cables. # Raise and support the vehicle. # Remove the battery lead from the solenoid terminal by pulling the rubber boot up and removing the nut # Remove the nut from the solenoid lead terminal at the solenoid. # Remove the starter mounting bolts # Remove the starter motor. # Reverse the removal procedures to install. Tighten the starter hardware as follows: #* Starter mounting bolts - 43 N·m (32 ft. lbs.) #* Solenoid lead nut - 6 N·m (55 in. lbs.) #* Battery lead nut - 10 N·m (90 in. lbs.)


How do you replace the starter on a 1997 Dodge Ram?

# Disconnect and isolate the battery negative cable. # Raise and support the vehicle. # Remove the nuts from the terminal studs for the starter battery lead and solenoid lead # Remove the hardware securing the starter to the bellhousing # Move the starter forward to clear the lower mounting stud (V-6/V-8 engine) and for the starter gear housing nose to clear the bellhousing. This allows the starter to come down past the exhaust pipe # Reverse the removal procedures to install. Tighten the starter hardware as follows: #* Starter mounting bolts to 68 N·m (50 ft. lbs.) #* Starter mounting nut - 27 N·m (20 ft. lbs.) #* Battery lead terminal nut - 14 N·m (120 in. lbs.) #* Solenoid lead terminal nut - 2.5 N·m (22 in. lbs.) == # Disconnect and isolate both of the battery negative cables. # Raise and support the vehicle. # Remove the battery lead from the solenoid terminal by pulling the rubber boot up and removing the nut # Remove the nut from the solenoid lead terminal at the solenoid. # Remove the starter mounting bolts # Remove the starter motor. # Reverse the removal procedures to install. Tighten the starter hardware as follows: #* Starter mounting bolts - 43 N·m (32 ft. lbs.) #* Solenoid lead nut - 6 N·m (55 in. lbs.) #* Battery lead nut - 10 N·m (90 in. lbs.)


What is problem a starter give in a truck a s 10 chevolet truck?

A prevalent problem with starters is that connections loosen and corrode; before suspecting a bad starter or solenoid, inspect, clean, and tighten all connections, including the ones at the battery. Also, insure battery is fully charged.


How do you change the starter in a 1997 ford f-150?

Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. Start the engine several times to check starter motor operation.


How do you change the starter on a 97 Ford Expedition?

Starter = Removal & Installation = 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.


Starter removal for a 2001 half ton f150?

StarterRemoval & Installation 1. Disconnect the negative battery cable.2. Raise and safely support the vehicle.3. Remove the starter terminal cover.4. Remove the terminal nut and separate the battery starter cable from the starter motor.5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.6. Remove the starter motor retaining bolts.7. Remove the starter motor from the vehicle.To Install:8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.11. Install the starter solenoid safety cap. If equipped.12. Lower the vehicle.13. Connect the negative battery cable.14. Start the engine several times to check starter motor operation.


How do you change the starter on a 1992 f150 6-cylinder?

StarterRemoval & Installation1. Disconnect the negative battery cable.2. Raise and safely support the vehicle.3. Remove the starter terminal cover.4. Remove the terminal nut and separate the battery starter cable from the starter motor.5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.6. Remove the starter motor retaining bolts.7. Remove the starter motor from the vehicle.To Install:8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.11. Install the starter solenoid safety cap. If equipped.12. Lower the vehicle.13. Connect the negative battery cable.14. Start the engine several times to check starter motor operation.


How do you wire up a starter for a 1995 ford truck?

StarterRemoval & Installation 1. Disconnect the negative battery cable.2. Raise and safely support the vehicle.3. Remove the starter terminal cover.4. Remove the terminal nut and separate the battery starter cable from the starter motor.5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.6. Remove the starter motor retaining bolts.7. Remove the starter motor from the vehicle.To Install:8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.11. Install the starter solenoid safety cap. If equipped.12. Lower the vehicle.13. Connect the negative battery cable.14. Start the engine several times to check starter motor operation.


How do you reconnect the wires to the starter of a 1994 ford f 150XL?

StarterRemoval & Installation 1. Disconnect the negative battery cable.2. Raise and safely support the vehicle.3. Remove the starter terminal cover.4. Remove the terminal nut and separate the battery starter cable from the starter motor.5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.6. Remove the starter motor retaining bolts.7. Remove the starter motor from the vehicle.To Install:8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.11. Install the starter solenoid safety cap. If equipped.12. Lower the vehicle.13. Connect the negative battery cable.14. Start the engine several times to check starter motor operation.


Starter installation for 97 expedition?

Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.


What extensions to use to remove the starter of a 2000 expedition?

Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.


Where is the starter on a 2000 Lincoln Navigator?

Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. Start the engine several times to check starter motor operation.


How do you replace the starter on a 2001 Ford Expedition?

Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. Start the engine several times to check starter motor operation.


How do you take off a starter for 1998 ford expedition XLT?

Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.


How do you install the starter on 2004 f150 stx 2wd?

Starter = Removal & Installation = 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.