Oldsmobile
Chevy Silverado
Chevy Venture
Oldsmobile Alero

How do you turn off the change oil light on 2000 Oldsmobile?

707172

Top Answer
User Avatar
Wiki User
2015-07-15 19:59:39
2015-07-15 19:59:39

I have a 2000 Olds Silohuette. I just reset the "Change Oil" light by turning the ignition to on(DO NOT START THE VEHICLE), pushing the accelerator down to the floor 6 times, turning the ignition off, and then starting the van. The light did not come on. Hopefully this will help.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

how to installing a turn light switat in 1995 Oldsmobile ciera

User Avatar

Turn your key to on, but don't turn the engine on. Pump the gas peddle three times slow and steady under 10 seconds that is. And then turn on the car and the light should go out!

User Avatar

If the change oil light comes on, then a person needs to change their oil. If a person changes their oil the light should turn off.

User Avatar

To turn off "change oil" light: # Turn off car. # Turn key to "on"; do not start it, just turn to "on" position. # Firmly depress accelerator three times, pausing for a second after each pump. # After 3 to 5 seconds, "change oil" light will flash and then turn off. # must depress gas pedal 3 times inside of 5 seconds, should hear a chime and the light will reset. This is found in the owners manual

User Avatar

Brake light, on your 2000 Chrysler Concorde, by accessing it from the inside of the trunk. Take hold of the brake light, push in and turn. The brake light will come out.

User Avatar

Reach in from the bottom of the fascia. The socket takes about a quarter turn.

User Avatar

2000 Oldsmobile Bravada turn signal light bulb replacement: Purchase the correct replacement turn signal light bulb(s) first, before disassembling the vehicle. See sources and related links below for replacement bulb information. Then consult your owner's manual for the turn signal light bulb replacement procedure. As simple as it sounds, the owner's manual is the best place to start for bulb replacement instructions and illustrations. You may want to consider replacing both left and right at the same time in order to keep brightness and color equal (optional).

User Avatar

The relay panel on the 2000 Oldsmobile Alero is under the steering column and above the brake pedal. The relay pops out with a screwdriver.

User Avatar

Remove the light assy and turn the bulbs counterclockwise.

User Avatar

how do ypu change front turn signal bulb on Oldsmobile 1991 cutlass cierra

User Avatar

Just unscrew the rear brake light, turn out the socket, and replace the bulb.

User Avatar

key on engine off...push gas pedal to the floor 5 timrs witin 3 seconds ..this will turn your lite out

User Avatar

How do you turn off the change oil light on a Chevysilverado 2002

User Avatar

The turn signal flasher relay on a 1992 Oldsmobile 98 Recency is in the fuse box under the dash. The fuse is light blue in color.

User Avatar

Turn on the ignition (switch). Depress and release the accelerator pedal three times within five - ten seconds. Turn off the ignition. Start the car; the change oil light should only light up during the self test. The mileage interval since the last reset will activate the change oil light. If you want to use the change oil light as your reminder for service, repeat this process immediately after an oil change.

User Avatar

Turn the key to run position Depress the accelerator pedal to the floor 3times in 5 seconds. The light should flash and the go out. Turn the key off and the start the engine.

User Avatar

Warning lights come on when there is an issue. A Oil change light with turn off when an oil change has taken place.

User Avatar

its part of the 4 way flasher its all one unit now

User Avatar

Open the hood, get to the back of the light, remove the rubber cover and the light is visible. Turn the light bulb housing and pull the bulb out. Installing is the reverse.

User Avatar

Turn car on but don't start the engin. Pump breaks a couple times. Turn Key to off then start engin all the way. Light should be off.

User Avatar

Hopefully you mean the "change engine oil" light and not he oil pressure light. Turn the key to the on position (do not start it), within 5 seconds press the accelerator to the floor 3 times. The change engine oil light should flash several times then go out. Who ever changed the oil should have done that for you.

User Avatar

Pop the trunk, remove the "3 wingnuts" behind or on the carpet. That will in turn loosen the tail lights. Turn the bulb, and voila!


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.