answersLogoWhite

0


Best Answer

You will need the Ford Hydraulic Clutch Quick Disconnect Tool.

User Avatar

Wiki User

13y ago
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How do you unhook clutch hydraulic line for ford ranger from transmission?
Write your answer...
Submit
Still have questions?
magnify glass
imp
Related questions

How do you unhook clutch hydraulic line for ford ranger from master cylinder?

Many of these, depending on year, came as an assembly and could not be disassembled from the line or the slave cylinder.


How do you change the clutch and master cylinder on a 1995 Ford Ranger 4-cylinder?

You have to drop the transmission. Be sure to unhook the battery cable first. Unhook all the line on the transmission. The is a quick release for the hydraulic clutch- to unhook it you have to push the white plastic in toward the transmission and it will pop out. Remove all the bolts on the transmission. You will have to undo the starter as well. You will need to buy a clutch kit. You should also have the flywheel resurfaced. The kit will contain an alignment tool that is shaped alot like the shaft of the transmission. The hydraulic system contains the slave cylinder which is located on the shaft of the transmission. I recommend changing it too. The Master cylinder is located above the clutch and under the hood you can see where the hose goes into the body of the truck to the clutch pedal. There are two bolts that hold it in. I haven't removed mine yet, but will tomorrow. Why are you replacing the master cylinder is it leaking or not holding pressure on our pedal? Then you will put it all together and need to bleed the slave cylinder and master cylinder. You need to follow the directions on the replacement parts. Hope this helps you.


How do you remove and install throw out bearing on a 2003 Honda Accord coupe 2.4 liter 5 speed?

The short answer: Pull the transmission and put a clutch kit in it. A Honda Accord clutch kit comes with the clutch disc, pressure plate, and a new throwout bearing.Once you get the transmission out, the throwout bearing is slid onto the transmission input shaft and is connected to the clutch arm. You unhook it from the clutch arm, slip it off the shaft and put the new one in its place.


How do you replace the clutch on a 1999 Honda Accord ex?

Long process broken down: You will need: Large tool kit Pickle fork (ball joint separator) and three-pound sledgehammer Jackstands Transmission jack Clutch kit Bottle of hydraulic fluid, just in case Enough Honda MTL to refill the transmission You should have: Help Steps: 1. Unhook battery, jack up car and remove front wheels. Drain the transmission. 2. Separate brake rotors from CV axles, then take axles out. Disconnect the clutch cylinder from the transmission. 3. Disconnect everything that will keep you from removing the transmission, and do that now. 4. Unbolt the old clutch and bolt in the new. 5. Put car back together. This will take you all weekend.


How do you repair or change the clutch in a 1997 Ford Aspire?

Remove the transmission. Take out the battery tray and remove the starter. Unhook the clutch cable and remove the bracket. Take out the speed cable and unplug a couple wire harness's. I removed hood of vehicle so i had more room. Support motor with a jack. Unhook the stablelizer bar and gear shifter. Put a jack under trans and crossmember. Unbolt the transmission and crossmember and it's ready to drop. Time your looking at 4 hours.


How do you repair a clutch in a VW Beetle?

assuming this is an older beetle beetle clutch is easy.jack up rear of car and place on jack stands. unhook engine electrical, throttle cable, fuel line, and heater box cables.place jack under engine,undo the four bolts that secure engine to transmission. remove engine.with engine out of car,access to clutch is easy. replace clutch and pressure plate. reinstall engine. an experienced mechanic can do this in 1 hour. If the problem was the cable,remove cable from transmission end, unbolt pedal assembly from center tunnel. clutch pedal has a hook inside the center tunnel that the cable hooks on. slide new cable into tube in center tunnel. replace pedal assembly, keep cable tight enough that it doesn't unhook while you put it back on the transmission end.adjust for correct freeplay


How do you remove clutch pedal assembly on F-150?

4 bolts to the master and 2 bolts to the column now you also have to unhook the brake peddle and the clutch


How do you replace the clutch in a 1984 F150?

Take out the battery tray and remove the starter. Unhook the clutch cable and remove the bracket. Take out the speed cable and unplug a couple wire harness's. I removed hood of vehicle so i had more room. Support motor with a jack. Unhook the stablelizer bar and gear shifter. Put a jack under trans and crossmember. Unbolt the transmission and crossmember and it's ready to drop. Time your looking at 4 hours


How do you reset the pcm on 1996 Ford Ranger?

Unhook the negative battery cable for 15-30 min


How do you replace clutch cable on 1968 vw beetle?

First, unhook the battery, block the wheels and jack up the left side of the car. Crawl under and look straight up from the axle; you will find the clutch lever on the side of the transmission. Unhook it. Then open the engine compartment and unhook the accelerator cable from the carb. Go into the driver's footwell and flip the gas pedal forward. You will see two bolts holding the pedal cluster on. Remove them, and work the cluster out of the hole it's in. If the clutch pedal goes all the way to the floor when you step on it, three things could have happened - well, four if you count the transmission breaking but that's the least likely to happen. First, the hook on the end of the clutch pedal could break. If that's what happened, it's held on with a little bolt on the side. Remove the bolt, slip out the old hook. Grease the shaft of the new one, stick it where the old one was and put the bolt back in. Second, the clutch pedal end of the cable could have broken and third, the transmission end could have broken. In either case, stick your finger into the hole the clutch cable is sticking out of and find the clutch cable tube. When you do, pull the old cable completely out. Grease the new one and work it into the clutch cable tube. When it's almost all the way in, put it on the hook and put the pedals back in place. Crawl under the car. Put the end of the cable through the clutch arm on the transmission, then screw on one of the two nuts - the other is a jam nut. Get someone to push the clutch pedal down 1/2" with their hand, and run the nut all the way up to the clutch arm, then put on the jam nut. Set the car on the ground, hook up the accelerator cable and reconnect the battery.


How do you change the clutch cable on a 94 Geo Tracker?

This is pretty simple. Disconnect the cable from the transmission then, follow the cable up through the engine compartment disconnecting the plastic clips along the way. Once you get to the firewall, use a socket to remove the two bolts holding it there. Go inside and unhook that end from the clutch pedal arm. Follow this process in reverse to install the new on and you are done!


How do you unhook odometer on 2002 Dodge Caravan SE?

you can't. the mileage signal is integral to the transmission shifting