0
How do you wire a light socket that does not have side screws to attach the wires to The wires go into little holes underneath on the bottom of the socket?
Wiki User
∙ 10y ago
These types of lamp sockets are known as pigtail sockets. Used in lighting fixtures they can not be repaired unless you have the means to re tighten the rivet that is used in the bottom of the lamp base. Any lighting store will have replacement parts for these types of fixtures. Molded pigtail lamp holders are used for temporary lighting in the construction trade. These lamp holders are positioned on brewery cord and can be placed at any needed position on the cord.
Wiki User
∙ 10y ago
Add your answer:
Earn +20 pts
Why does a non grounded plug have four screws for two wires?
Typically the silver screws are neutral, the brass screws are for "hot" (if there are silver screws) There are two on each side because that gives you options. You can feed into the plug box and connect to one pair of screws, then subfeed the next circuit using the other pair. OR you can separate the circuits so that the top and bottom halves of the plug are either on a separate circuit or one half can be on a switch. The options are there if you want to use them. To separate the top and bottom half you'd need to break away the jumper between the top and bottom halves of the plug.
How can one replace a cabinet hinge?
To replace a cabinet hinge, you must first remove the screws that attach to the door with either a screwdriver or a drill with screw bit. Next you want to remove the cabinet door. Once you have removed the door, remove the hinge from the cabinet. You can then attach a new hinge. A nice tip is to have a partner hold the door while you screw the hinge back in place.
What device controls the mixture of gas and air going into a gas engine?
If the car is carbureted then there are two little screws on the carburetor called air/fuel mixture screws that control the air/fuel mixture. There should be info. on your cars factory settings. Hope this helps.
What kind of screws does a metal futon use?
Confirmat Screws
How do you install a 110 volt plug?
I'm first off assuming this is a brand new plug, not a replacement. Okay. Ground first(green). Make sure you've got enough bare copper to wrap around the bottom screw. Then, strip and wrap the white around either of the silver screws on the side of the outlet. Finally, connect the black to the hot side (brass colored screws). And you should be all set.
How can you open a Creative Fatal1ty 1010 mouse?
Lift up the white pads on the bottom. Screws are underneath.
What is the purpose of screws?
To attach things together.
Where is signal flashers on 1996 Chevy S-10 pickup?
I have a 1997 and mine are underneath the Cig lighters. Take the bottom panel screws out and you should see them. I changed mine with only taking several of the screws out. Good luck!!!!!!!!!!
How do you remove the driver side front door panel on a 1996 Toyota Camry?
just undo all the screws on the door, and when you see those little cover pieces that are an off color from the rest, take a Philips screw driver and pry those off because there are extra screws underneath. Remember to take the cover off the inside door handle, and there will be screws on the bottom of the door panel. Good luck
Where is the starter motor on a vauxhall astra?
at the back of the engine underneath the oil filter. one bolt on the bottom side of starter the top bolt screws in from the gear box side
How easy is the Under Counter Keyboard Drawer to mount?
The Under Counter Keyboard drawer mounts to any desk or shelf by the folding brackets that attaches underneath. The brackets are already attached, so you only have to attach it with the screws.
How do you remove the ignition switch tumbler on a 1986 dodge lancer 2.5?
Remove the screws on the side of the steering column. Remove the screws underneath the steering column and pull the bottom half of the column down. Slide a pin punch into the hole at the ignition tumbler assembly's bottom. Force the tumbler upwards and pull it out of the steering column.
How do you replace a fuel pump in a 1995 Mazda miata?
underneath the carpet behind the seats there is an access point. unscrew the screws and lift off the cover. then there is another screwed on cover with two gas lines coming from it. It has about * or so tiny screws in it. these screws are extremely easy to break, so smack them with a hammer first to loosen them. dissconnect the hoses to the top of this cover first, and the little electrical plug thing, and pull it out. the fuel pump is connected to the bottom of this cover.
Where is the thermostat located on a 2004 Subaru Outback?
In a 2004 Subaru Outback, the thermostat is located on the bottom of the engine on the driver's side. Remove the screws holding the fitting that the hose (from the bottom of the radiator leading to the engine block) is attached to, remove the fitting, and the thermostat will be underneath.
How to Attach front license plate to ford escape?
Usually you can get a license plate holder from a dealership that screws on to the front bumper somewhere then you mount the plate to this holder. If you dont have one of these then you will have to attach it to the bumper area using screws, wire, zip ties, or any other creative way to attach it. If using screws I recommend using stainless steel screws so that they wont rust. You can get these at any auto supply store. Good luck.
How do you replace the headlight bulb located on a 1996 Jeep Grand Cherokee Limited?
just pop it out.. its not held in with any bolt or screws.. just grab and firmly pull it out forward. Its held by little snap type balljoint like connectors that attach to the adjustment screws.
How to remove 2004 sonata glove box?
The 2002 Jeep Grand Cherokee glovebox is secured with a retaining screws. There are four retaining screws on the top and for retaining screws on the bottom of the glovebox. Remove the retaining screws to remove the glovebox.
