0
In the open position
Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
What is the voltage to a sprinkler valve from the control panel?
Most common North American garden sprinkler systems use 24 volts AC. The control units usually plug into a common 120 volt AC receptacle. Inside the control unit there is a transformer that reduces the voltage from 120 volts to 24 volts AC. If you look on the side of the sprinkler valve coil you will see the voltage and the amperage draw of the coil. It is the amperage draw of the coils that determines the number of sprinkler that should be on one sprinkler branch from the main water manifold. The total amperage of the circuit determines what the size of the wire should be to control the sprinkler coils.
Orbit Sprinkler Valve?
form_title= Orbit Sprinkler Valve form_header= Keep your lawn healthy with a sprinkler. Do you need to replace a sprinkler valve?*= () Yes () No How many valves do you need?*= {1, 2, 3, 4, 5, More than 5} How old is your current sprinkler?*= _ [50]
What causes sprinkler valve chugging?
Static pressure.
Why 2 provide valve springs?
To provide the correct valve spring pressure. Easier to customize/work with thinner wire. Easier to cool the wire with oil. Easier to control harmonic vibrations in the valvetrain.
Where is the heater valve on a 1988 Chevy truck?
The heater valve is in line in the heater hose from the top back of the 350 engine about half way to where it enters the firewall to connect to the heater core. The valve has a steel wire control cable connected to the top of the valve control lever. It has two hose connections, one in from the engine and one out to the firewall core entry point. Trace your heater hoses and look for the metal valve with the spiral covered control wire.
How do you turn off a fire sprinkler tamper alarm?
First you locate the source of the alarm, undo the condition (e.g., valve closed, inadequate pressure, etc), then reset the alarm condition on the sprinkler control panel and reset the alarm on the fire alarm control panel (assuming they're connected, as required by many fire codes).
How do you wire air brake switch on a truck?
Assuming you're talking about a brake control valve, there is no wiring...
When checking a sprinkler system a security officer should do what?
ensure valve is closed
How do you install a sprinkler system?
There are two main methods of sprinkler system installation: open trench and pulled pipe. Open trench typically uses PVC pipe and pulled pipe typically uses poly pipe. Other than the pipe and fittings, the main difference in installation will be that the pulled pipe system requires a hole and saddle tee at the location of each sprinkler head. The steps for installing an automatic sprinkler system using an open trench method are: 1. Start with a good sprinkler system design (try searching "sprinkler system designer" for support options) 2. Make sure that you have all necessary tools, equipment, and permits 3. Have Blue Stakes mark all utilities prior to any digging 4. Install a backflow prevention device according to code 5. Place flags at the location of each sprinkler head 6. Mark and dig all trenches and valve manifold locations 7. Build and install valve manifolds (preassembled valve manifolds can make this easier) 8. Connect mainline pipe from water source connection to valve manifolds 9. Lay lateral line pipe from the valve manifolds to the location of each sprinkler head 10. Install tees and swing assemblies for each sprinkler head and flush lines 11. Connect sprinkler heads to swing assemblies; set head to level with ground 12. Install sprinkler timer/controller and connect sprinkler wire from timer to valve manifolds 13. Install nozzles on sprinkler heads 14. Install valve boxes (as required) and backfill all trenches 15. Run a zone by zone test and adjust nozzle patterns
What is a Fire Sprinkler alarm valve?
Some fire sprinkler systems have a valve for testing the water-flow alarm by allowing water to flow to the alarm, or through the alarm-sensing pipe, without activating any sprinklers in the rest of the system.
Why is the lawn sprinkler head leaks water when the main water valve is shut off?
After a main water valve is closed the system's PVC pipes are still full of water and will drain to the lowest sprinkler head until the system is empty.
Where is idle air control valve on 1999 dodge durango 3.9l?
It is the four wire item on the back of the throttle body.
