You don't. A 2 prong plug has two wires, one called live (black or red wire in the US) and the other is neutral (white or gray wire in the US). A 3 prong plug needs a third wire for ground (bare copper, green, or green-yellow in the US).
The only time you can replace a 2 prong plug with a 3 prong plug is if the 2 prong plug incorrectly replaced an original 3 prong plug.
The third wire that you don't have is the earth, so therefore you have a live wire and a neutral wire. If you are in England the live wire will be brown and the blue is neutral. As you look at the underside of the plug (with the three prongs staring up at you) the prong on the left is the neutral pin, so attach the blue wire there. (with a small screwdriver to secure it in the hole - you will find a small screw that clamps the wire in the hole.) The live (brown) wire attaches to the pin on your right, and usually the place to put it is obscured by the fuse, so you may need to take the fuse out, secure the wire in the hole, put the fuse back, and that's it. The plastic sleeve at the bottom (where the wires enter the plug needs to be screwed over the two wires to clamp it in place. This prevents the wires from being accidentally pulled out. Put the plug back together and it should work.
You have two options. The first and best option is to change the receptacle to a three wire outlet. Ground the receptacle's green terminal to the back of the electrical box where a ground wire should be attached. If there isn't one don't worry about it. The second option is to buy an adapter that allows a three wire cord to be plugged into a two wire receptacle. On this type of adapter there is a wire that has to be connected to the center screw that holds the receptacle cover plate on.
A typical three prong residential outlet for 120 volts has a brass colored, a silver colored and a green screw. Connect black wire to brass, white wire to silver and bare ground wire to green.
Yes, we can use 2 wires on a 3 pin plug. Because in 3 pin plug usually tall pin called and used as a earthing pin which is used for safety purpose. So if anybody use 2 wire, that pin would be neglected but other would be worked.
Click the link.
See discuss question.
yes
unplug old cord...plug in new cord
you can buy a flash drive or you can buy something that you plug into a usb port and you save stuff on or you can send them trough email
A disadvantage of fifth generation computers is that they can give more power to companies to watch what you are doing and even allow them to infect your computer. Another disadvantage is that they tend to be sophisticated and complex tools.
Well for starters you can reprogram it by buying a PROM chip and programming it and replace the old one with the new Programmed one. Or you can buy a whole new programmed after market PCM or Computer.
No you can not you will need to replace the plug with a 4 prong the same as the style of your oven and change your breaker to the correct Amp for your style of 4 prong plug
To replace the flasher on a VW Beetle, locate the flasher under the dash on the driver's side. Remove the old flasher and replace with a new one. This is not a fuse, but a three prong plug in that looks like a small cylinder.
The turn signal flasher is a three prong plug in on a Toyota Rav4. It is located under the dash on the driver's side of most Toyota vehicles. Take the old plug out and insert the new one.
To replace the flasher relay on a 1998 Nissan Pathfinder 4WD, unplug the old turn signal flasher and plug in the new one. It is a three prong plug located under the dash on the driver's side. The hazard flasher relay works the same way.
The replacement plug will most likely come with short pigtail wires. The old wires will have to be cut and spliced to the new wires. Make sure that the connections are sealed from the weather as this is an area that gets wet.
Install an AFCI breaker on the circuit with the outlets you replace and you will be fine.
To change the turn signal flasher on a 1993 Toyota Corolla, locate the flasher unit under the dash on the driver's side. Pull out the old flasher plug and replace with a new one. This part has a three-prong plug that can be removed without hooking up or unhooking wires.
You have to go buy a new four prong chord, unscrew the base of the old chord, and switch them out.
you take the old one out and replace it with the new one... hope this helps
Get pre gapped plugs from dealer (irridum not platinum remove engine cowling remove coil wire remove old plug replace with new plug replace coil wire and cowling
All three prong dryer cords should fit all three prong outlets. Dryer and stove plugs are different but as long as someone didn't use one in place of a dryer cord, there isn't a problem.
.030 Refer to your owners manual of remove the old plug and just replace it with an identical plug.