answersLogoWhite

0

  • 2000-2005 Dodge & Plymouth Neons

How hard is it to change the rear struts on an 2000 dodge neon?

User Avatar

Wiki User

βˆ™ 2008-07-15 18:08:13

Best Answer
Copy

not hard at all,you will need a spring compressor

2008-07-15 18:08:13
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Add your answer:

Earn +5 pts
Q: How hard is it to change the rear struts on an 2000 dodge neon?
Write your answer...
Submit

Related Questions

How do you change rear struts on a dodge neon?

leave this to the pros, struts are hard to do safely without special equipment to compress springs


Does a 1999 Ford Contour have struts in rear?

Yes they do have struts and they aren't hard to change


How hard is it to change the rear struts and springs on a 1997 ford escort LX if the used struts and springs come connected already?

It's easy.


How hard is it to change the hubs on a 2003 dodge piuck up truck?

i would like to know how hard is it to change the front hubs on a dodge truck?


How do you change the struts on a 2002 Chevy Prizm?

You need a special strut spring compression tool. Very very difficult to do it by yourself, unless you have this tool. Getting the struts off is not too hard, putting the new strut in is the hard part.


How do you change the fan blower motor on a 1998 Dodge Intrepid and how hard is it to change?

dont have a clue :)


Is it hard to change a 2000 Volvo v40 steering rack?

Very hard


How hard is it to replace the rear struts on a Saturn 2002 L200?

how to replace rear struts on a 2002 saturn L 300


How hard of a job is to change a timing chain on a dodge intrepid 3.3 motor?

With the proper tools and information it is not a hard job.


How hard is it to change the timing belt on a 1990 Dodge Colt 1.8 liter?

Very.


How do you know when a fuel pump is going out on a 2000 dodge grand caravan?

Noisy pump, hard starting, stalling.


How hard is it to replace struts?

It isn't hard at all aslong as you have patience and alittle know how. Be warned I highly suggest you take the struts once removed from the car to a service center to have them remove the strut from the springs!


Nissan Maxima fuel filter change?

How hard is it to change a 2000 Nissan maxima fuel filter


What would cause a hard brake pedal on a 2000 dodge stratus and this car does not have ABS?

this could be you're ABS sensor


Location of fuel filter on 2000 dodge stratus es?

it's back at the gas tank. kinda hard to get to!!! I think top front! Fuel pump too if I'm not mistaken. I have the same car. If you can afford it, change both!!!!


Having a hard time removing a crankshaft pulley off a 2000 dodge neon?

You have to purchase a special pulley puller from Dodge, other wise you will break the pulley when you try to pull it off.


What are the release dates for A Little Curious - 1998 Hard Easy Change?

A Little Curious - 1998 Hard Easy Change was released on: USA: 11 March 2000


What makes a Car hits hard when going over bumps?

bad shocks or struts


What if you don't see a fuel filter in a 2001 dodge stratus?

Where are you looking? In my 2000 it's in or on top of the gas tank. Kinda hard to get to but it should be there!


How many quarts of oil 2000 Dodge Intrepid 2.7l 6-cyl engine?

I have a 2001 2.7 L Intrepid and it takes 4.5 quarts


Reinstalling struts.took the worn struts offhaving a hard time installing the new one's.?

what vehicle


On a 1998 Dodge Intrepid 2.7 when you try to move the shifter to park it feels hard to change what could be causing this problem?

this sounds like a problem i had on my 2000 you need to look into having the shifting cable replaced. some of the late 90 models have had a recall on the shifter and if you are in that recall, you can go to a dodge dealer and they replace it for free, that was my case.


Is the a c compressor hard to change 2000 Beetle?

No it's like changing an alternator but you will have to recharge when done.


A dodge ram 2500 diesel 2001 is the ecm hard to replace?

is the ecm on a dodge 2001, 2500 diesel hard to replace??


How do you change 2001 dodge ram 1500 disk brake pads?

go to a shak and ask a dude to do it for you, it's too hard to do on by your self