2.7 seconds.
Slide down the front panel on the KLIK1U remotePress the program button (top right), holding it down until the LED lights up (and stays lit)On your overhead garage door opener, press the "Learn" buttonOn your remote, press the button you want to assign to that door -- waiting each time for the LED to stop blinking.Once your garage door opens, press the program button on your remote once more .... and you are done.
How to program remote garage door openeYour owner's manual has complete instructions on how to do this. But, it requires that you have the remote opener provided by the garage door company. On my Buick, you just hold the button on the car's opener and the remote at the same time. The car's opener will beep and this should do it. Try thisStep 1: hold the hand help remote 3 inches away from the button you choose to program in your vehicle and hold down bothe buttons (hand held remote button and vehicle button) you should see slow blinking lights on your vehicle buttons. Once they change to rappidly, let the buttons go.Step 2: on the garage door opener itself, you have a learn button( usually located next to your lights on the garage door opener) push and let go the learn code, a light will appear on above that button, then you will have 30-45 seconds until that light goes off.Step 3: go back to the vehicle, push and hold the button you chose to program from step 1, until you see the garage door opener lights blinkIf that happens then the button is trained. Hope that helps you.Please leave a cooment on my website, and let me know how it worked.http://www.valleydoors.webs.com
remote button may be stuck.
You can program the remote start by holding the start button down for 10 seconds. The start light will illuminate. With the start light illuminated hold the start button down until the engine start.
If it is a newer model with multi-function wall control, first push and hold remote button then light button then button that opens and closes door so you are now pushing all three buttons simultaneously then release all three and remote should be programmed.
To program a GPT universal remote control, hold down the power button at the same time with the button for the device that is going to be programmed. When the other buttons on the remote blink, let up and press on the power button again. The device should turn on. If not, repeat the process.
Hold the 2 outer buttons down until the light in the little house icon flashes rapidly. That will clear the memory. Then you hold down the button on your opener remote while pushing the button you wish to program. When the flashing light changes from slow to rapid, you should be all set. If your opener has "rolling code" technology, you will have to program that by pushing your opener button in the car while somebody pushes the "learn" button on the opener itself.
hold down device button when entering the 4 digit key
When you are parked close to the door opener hold down the button until the light becomes slower.
On my RX 350 and Craftsman opener I just pushed the memory button on the Craftsman opener briefly (the signal light came on next to the button) and released it. Then I pressed the sender in my car within 30 seconds. It wasn't long before the lights on the opener flashed and I then released the Lexus button. Didn't have to hold anything down very long at all.
Short answer: Hold the built-in button down and your garage door remote control button down at the same time and near each other. The built in will flash slow then fast once it gets the code (takes up to 1 min). - that's it - but... I have a Genie Garage door opener and remote and I had some problems that figured out (don't want to rewrite it here) so I cut and paste this: (sent to Genie) Just wanted to let you know that I figured out how to use my XK8 built-in garage door opener but there was a glitch that I had to work through. I actually had to program the built in remote with my Genie Intellicode Transmitter (GIC/GIT-1,2, or 3) (that worked to program my built-in remote but it wouldn't work on the genie pcg650 garage door opener?) I then used your Rcvr Programming Instructions to program the "genie pcg650 garage door opener receiver" with the cars built-in opener (that I had just programed with youf Intellicode remote. Beleive it or not when I was all done the intellicode remote and the Car's built-in remote both worked. It was like the built-in remote got the correct code but the receiver had to learn that it was OK to accept it from the built-in? Anyway, your sight helped a little and I thought you could help others with this info. Thanks Danny
A popular way to open garage doors is the universal door opener because it is compatible with a wide variety of door models. The universal remote can control both doors of a multi-bay garage and keep you from needing two separate remotes. Program the remote by holding down the buttons until the LED indicator turns red. Select the button that will be used to open the garage. Press and release that button the number of times that the instruction manual says is required for that door model. To finish the programming, hold the chosen button until the LED blinks.