A low voltage fuse should be rated for 30 amps.
There is no such thing as fuses are rated in amps, not volts. a 10 amp fuse will protect against anything over 10 amps regardless of the voltage used.
Depends on the voltage across the fuse. For fuses rated below 9 amps, the two types are almost identical (MDL has slightly lower AC Interrupting amperages), and both are rated for use up to 250V. For fuses rated above 9 amps, the MDL fuses are rated for use up to 32V, while the MDA fuses are rated for use up to 250V. More info on Cooper Bussmann (link below).
# 10 wire is rated at 30 amps. Code states the the wire is only to be loaded to 80%. 80% of 30 = 24 amps. If distance is a factor then the resistance of the wire comes into play. Go up one size to #8 rated at 40 amps, usable 32 amps.
No, use a fuse rated for the proper voltage.
Both legs of a 240 branch circuit need to be fused with a fuse rated at 240 volts or better. The voltage potential across the load is what governs the fuse voltage ratings.
There is no such thing as fuses are rated in amps, not volts. a 10 amp fuse will protect against anything over 10 amps regardless of the voltage used.
Fuses are rated by amperage (current) and voltage. The larger the current need, the larger the rating of the fuse, to handle the current. The voltage rating of a fuse defines the maximum value of circuit voltage in which the fuse can be safely used. A fuse should not be used in a circuit with a voltage exceeding the voltage rating of the fuse.
The fuse will fail at 50 amps regardless of which voltage you use.
Most `T' fuses are rated in either 125 volt or 250 volts A.C. If you look at the metal end cap on one of the ends, it'll specify which voltage it's rated. The 1.25, is 1.25 amps at the rated voltage.
If the 2 amps is the output amperage of the power supply, the maximum that should be drawn from the unit is 2 amps. The load amperage that is connected to the power supply should govern the amperage of the fuse used. There is not much range there, the fusing could go from .25 to 2 amps. If the input amperage is 2 amps then the input and output voltage of the power supply should be stated.
Depends on the voltage across the fuse. For fuses rated below 9 amps, the two types are almost identical (MDL has slightly lower AC Interrupting amperages), and both are rated for use up to 250V. For fuses rated above 9 amps, the MDL fuses are rated for use up to 32V, while the MDA fuses are rated for use up to 250V. More info on Cooper Bussmann (link below).
# 10 wire is rated at 30 amps. Code states the the wire is only to be loaded to 80%. 80% of 30 = 24 amps. If distance is a factor then the resistance of the wire comes into play. Go up one size to #8 rated at 40 amps, usable 32 amps.
20hp = 14.92kW 14.92kW / X Voltage= X Amps Rule of thumb for fuses: X Amps x 1.5 = Y Amps Fuse Rule of thumb circuit breakers: X Amps x 1.2 = Y Amps Circuit Breaker
5 Amps. If the current passing through the fuse exceeds 5 Amps is should "blow".
fuse "B" is for front wipers,fuse "D" rear wipers.both rated at 15 amps.
The formula you are looking for is Amps = Watts divided by Volts. Once you find the amperage you can decide as to the size of a fuse you should use. Remember that fusing protects the conductors of the circuit and not the load of the circuit. A #14 wire is rated at 15 amps and can legally be loaded only to 12 amps.
The fuse for the brake light on a Hyundai Accent are found in the engine compartment. The fuse is number four in the fuse box, and is rated on 10 amps.