hps light averages 125 lumens, therefore, a 150 watt hps light is about 18,750 lumens.
15000
A higher wattage HPS bulb may work with a ballast that is rated for a lower wattage bulb , but may appear to be dim and will not produce the rated light output. It is best to match ballast and bulb accordingly.
About 1.66 amps at 120 volts Ballasts have stickers on them that tell you the exact amps per the voltage that you are running
In most cases a cfl bulb can be replaced with an incandescent bulb as long as the base matches. for an example: if a cfl bulb has a GU24 base an incandescent bulb will not work! Also, ensure the wattage of the bulb does not exceed manufacturers rating.
Not recommended. It would work but shorten lamp life and may cause risk of fire. However, if you just wanted to check a lamp was capable of striking it would be ok for a few minutes. I've done the opposite in the past and used a 150w lamp with a 100w ballast. Works, but not good for any of the components, including lamp.
I actually have a 400w hps ballast and I can also use my 400w metal halide bulb in it with no problem. So what your saying is they do, but they dont? the answer is, they dont. You can get universal bulbs hps to plug into a mh ballast they have a miniturized igniter inside the bulb. As I understand it, a 400W metal halide bulb can be used with a 400W hps ballast, but not the converse. A MH bulb has the igniter in the bulb, and the HPS has it in the ballast--which pretty much goes along with your comment above. Apparently the double presence of the igniter in the HPS setup is OK.you can run metal halide in same wattage's but not hps in metal halide systems.you can run such as (same wattage's)250 watt metal halide-400 watt halide ect in hps systems but not hps bulbs in halide systems. they make conversion bulbs to run halide in hps as well and vice versa.
No!
When you want to use a MH bulb in an HPS ballast you must use a conversion bulb. It must be the same wattage as the HPS bulb
A higher wattage HPS bulb may work with a ballast that is rated for a lower wattage bulb , but may appear to be dim and will not produce the rated light output. It is best to match ballast and bulb accordingly.
About 1.66 amps at 120 volts Ballasts have stickers on them that tell you the exact amps per the voltage that you are running
In most cases a cfl bulb can be replaced with an incandescent bulb as long as the base matches. for an example: if a cfl bulb has a GU24 base an incandescent bulb will not work! Also, ensure the wattage of the bulb does not exceed manufacturers rating.
No, the ballast has to be matched to the lamp. 250 watt ballast, 250 watt lamp. Also be sure to match the lamp type to the proper ballast even though the wattage is the same. HPS ballast to HPS lamp, Metal halide ballast to metal halide lamp and mercury vapour lamp to mercury vapour ballast.
Not recommended. It would work but shorten lamp life and may cause risk of fire. However, if you just wanted to check a lamp was capable of striking it would be ok for a few minutes. I've done the opposite in the past and used a 150w lamp with a 100w ballast. Works, but not good for any of the components, including lamp.
yes
In general no, because the extra heat produced would make it a fire hazard.
I actually have a 400w hps ballast and I can also use my 400w metal halide bulb in it with no problem. So what your saying is they do, but they dont? the answer is, they dont. You can get universal bulbs hps to plug into a mh ballast they have a miniturized igniter inside the bulb. As I understand it, a 400W metal halide bulb can be used with a 400W hps ballast, but not the converse. A MH bulb has the igniter in the bulb, and the HPS has it in the ballast--which pretty much goes along with your comment above. Apparently the double presence of the igniter in the HPS setup is OK.you can run metal halide in same wattage's but not hps in metal halide systems.you can run such as (same wattage's)250 watt metal halide-400 watt halide ect in hps systems but not hps bulbs in halide systems. they make conversion bulbs to run halide in hps as well and vice versa.
The MH ballast will not have the ignitor required to power up the HPS bulb. I have 1000w ballast that can be switched between HPS and MH with a singe switch just by disabling the ignitor for the MH. I would look into conversion bulbs, or else check out this site for $20 150w HPS ballast with bulb. http://www.e-conolight.com/Product/EProductDetail.asp?ProductFamilyID=7&FGNumber=E-MT6H151G If it doesnt appear, sellect vapor tights, then the 150hps.
No high pressure lbs require a specific ballasts to operate the bulb correctly