0
How many pounds of rebar are in a typical concrete slab on grade?
Wiki User
∙ 8y ago
There is no way to answer without a design and the square footage.
Wiki User
∙ 8y ago
Add your answer:
Earn +20 pts
How do you strengthen concrete with reinforcing rod?
Rebar is used to strengthen concrete because of its strength and flexibility. In order for these rods to work, there must be ample space between the rebar and the edge of the concrete piece.
What is the difference between lap splice length and development length for rebars?
The difference between the two is in the application. A development length is the amount of rebar length that is needed to be embedded or projected into concrete to create a desired bond strength between the two materials. The lap splice length is the length two rebar pieces must overlap and be tied together to create a bond as if there was no break and the run is "continuous". So simply put, development is rebar to concrete, splice is rebar to rebar. The lengths of both splice and development do vary. They are dependent upon different factors. These include but are not limited to concrete strength, rebar size, rebar coating and concrete cover or clearance. So when you see a chart on one project, it can differ from another for these reasons.
Roads are made up of what?
sand gravel, asphalt, pavement, concrete, and rebar
Why do builders put metal rods in concrete?
Rebar is used as a tensioning device in reinforced concrete and reinforced masonry structures holding the concrete in compression.
How much does reinforced concrete weigh per cubic yard?
Normal weight concrete -- a mixture or sand, cement, and stone gravel -- has an accepted density of 145 pounds per cubic foot. Since there are 27 cubic feet per cubic yard, a cu.yd. weighs 3915 pounds, or almost two tons. Complicating your question is the word "reinforced." Reinforced concrete has steel bars in it, called rebar. Steel has a density of about 490 pounds per cubic foot, which is more than three times the density of concrete, so the generally accepted density of normally reinforced concrete is 150 pounds per cubic foot which results in a cubic yard weighing 4050 pounds, but this depends on the quantity and grade of the rebar used. (Ref. AISC Steel Construction Manual, 13th Ed. Page 17-24. Also older editions have this same information.) There is light weight concrete made with lighter weight substitutes such as vermiculite for the stone and sand. These can have weights from 85 pcf. Also, there are heavy weight concretes made with steel punchings or pieces of lead used to line rooms for x-ray machines or other radioactive sources. There is a Wikipedia article on rebar, if you're interested in looking it up.
How many pounds of rebar are in typical concerete per cubic yard?
It would depend on the CY of concrete. For example, a cubic yard of concrete in a transferbeam will have FAR more rebar in it than a simple stem wall. I believe 150lb/cy is used pretty widely for general estimating purposes but should be adjusted depending on what you're estimating.
How do you strengthen concrete with reinforcing rod?
Rebar is used to strengthen concrete because of its strength and flexibility. In order for these rods to work, there must be ample space between the rebar and the edge of the concrete piece.
What were houses made of in colonial life?
Concrete & rebar
What are rebar use for?
Rebar locators are used to find exactly where the reinforcing steel is located under concrete in existing materials. They are most often used for renovation or remodeling projects.
What is a typical unit weight pcf of rebar?
490pcf
Is cement conduct electricity?
Concrete it self may not but most concrete structures .Has rebar in them and that can .
What is meant by reinforcement in concrete?
Items used to reinforce concrete are wire mesh, rebar, and steel cables.
How much steel required for 1meter cubic of conceret?
It depends on how much rebar you're willing to lay down, in earthquake prone areas and structural concrete you'll generally see a lot of rebar, in just normal paver concrete you may not see any. Rebar is used to give concrete flexibility without brittleness so it really depends on the use of the concrete.
Is epoxy required in rebar connections?
Epoxy is not required in rebar connections as concrete and wire are used to hold it in place. Rebar is a reinforcement place inside masonry structures to provide increased strength.
How many tons rebar in a cubic meter of concrete?
average of 0.12tons of rebars per cubic meter of concrete.
What is the difference between lap splice length and development length for rebars?
The difference between the two is in the application. A development length is the amount of rebar length that is needed to be embedded or projected into concrete to create a desired bond strength between the two materials. The lap splice length is the length two rebar pieces must overlap and be tied together to create a bond as if there was no break and the run is "continuous". So simply put, development is rebar to concrete, splice is rebar to rebar. The lengths of both splice and development do vary. They are dependent upon different factors. These include but are not limited to concrete strength, rebar size, rebar coating and concrete cover or clearance. So when you see a chart on one project, it can differ from another for these reasons.
Crossword-Concrete reinforcer- five letter word beginning with r?
rebar
