Best Answer

4 wires, the black ones are the O2 heater (on the sensor side), the white and green are the O2 sensor itself

User Avatar

Wiki User

โˆ™ 2008-06-12 06:21:55
This answer is:
User Avatar

Add your answer:

Earn +20 pts
Q: How many wires does a 1995 Honda civic lx oxygen sensor have?
Write your answer...
Related questions

How do you replace oxygen sensor in Honda civic?

The oxygen sensor on a Honda Civic is replaced by disconnecting the wiring harness and removing the sensor using a socket wrench. Anti-seize paste is applied to the threads, a new sensor is torqued into place, and the wires reconnected.

What does an o2 sensor look like on Honda civic dx 1998?

the o2 sensor is in the exaust manifold or down pipe it looks like a sparkplug with wires

How do you replace the spark plug wires on a 2002 Honda Civic?

The 2002 Honda Civic EX engine uses coil-on-plug. There are no sparkplug wires.

Will Honda Accord spark plug wires work in a Honda Civic?

yes they will

A complete wiring diagram for 1994 Honda Civic is?

what are the wires to power up the ecu on a 1994 Honda civic si

Where is the coolant temperature sensor located on a 1995 Honda Civic EX?

Follow the lower radiator hose from the radiator to the back of the engine. Where it connects to the engine, you will see wires plugged in to the sensor

03 Honda accord oxygen upstream sensor locaton?

A 2003 Honda Accord Oxygen sensor is located on the exhaust pipe. To find it jack the car up and safely position it on jack stands. Crawl under the vehicle and look at the downpipe of the exhaust, the sensor will have two wires protruding from it.

What are the 1998 Honda civic ex tail light wires called?

Tail light wires.

How do you replace an oxygen sensor in a Honda Civic?

I replaced the ozygen sensor on a 1995 Civic VX (Hatchback). The part (the oxygen sensor) is rather expensive at more than $300, but easily removed and replaced. Once you have the new part, open the hood and look for a couple of wires coming out of the center of a silver bar (the header). These wires should connect the oxygen sensor to a wiring harness. Disconnect the harness and start the car to see if the ENGINE light is now off. If it is ... sucess. Use a wrench to unscrew the unit from the header and replace by reversing the process. Finish by re-connecting the oygen sensor to its wiring harness. The ENGINE light should stay off. If it comes on again, you have other problems.

Can an oxygen sensor be disconnected at the sensor?

usually there is about a foot of wires coming out of the sensor and then there is a clip that connects to another set of wires

Where is the heater oxygen sensor bank 1 sensor 1 located on a 1999 Honda civic dx 1.6L?

The bank 1 sensor is located front and center on your engine. It looks somewhat like a spark plug. It has 3 wires leading into it from a wiring harness located about 12 inches to the left of the sensor. It is at the top,front of the engine,partially covered by your exhaust shroud.

Where is water temperature sender on 95 Honda civic?

follow the top radiator hose to the engine block. the temperature SENSOR has two wires. The temperature SENDER has one wire

What is the distributor wiring route for spark plug wires in a 96 Honda civic dx?

The distributor wiring order for a 1996 Honda Civic is 1-3-4-2. The distributor will be have the wires in the clockwise position starting a 1.

How do you Change Oxygen Sensor 2000 Honda accord?

An O2 sensor unscrews like a spark plug and then there are 1-3 wires to rehook up.A special socket may be needed on some models.

Wiring for power side mirror on Honda civic?

The power mirror, on your Honda Civic, has three wires. There is a red hot wire, a black ground wire, and a white auxiliary wire.

How do you reset the airbag light on a 1994 Honda Civic?

To reset the airbag light on a 1994 Honda Civic locate the wiring for the SRS unit underneath the dashboard. There will be a yellow clip that connects to a fuse box. Unplug it and jump the sensor using two small wires. Turn the car on and off twice to reset the light.

Where is the oxygen sensor on a 1990 pathfinder located?

The oxygen sensor is located on the exhaust manifold and is the only item on the exhaust with wires going to it.

What causes 1989 Honda civic to cut out under acceleration?

it could be many things that cause this. I'd start with a general tune up. Spark plug and wires air and fuel filter oxygen sensor and oil/filter. If this doesn't help then try the main relay. good luck

What is the location of the IAT sensor on a 1995 Honda civic LX 1.5 liter?

Plugged in the intake manifold and the wires/plug are green/white and red/yellow colored according to what I see on the service manual

I'm having my dad replace the Oxygen Sensor on my 2000 Honda Civic Si and he wanted to know how to locate and replace the sensor?

Tell your dad to look on the exhaust right after the manifold, there may be 2 of them 1 before the catalytic converter and one after but most likely only the one. It is the only thing attached to the exhaust system with wires connected to it, he may want to get the o2 sensor removal tool which is a deep socket with a slot in the side so you dont mess up the wires.

Is there a diagram for the headlight wires in a Honda civic?

Yes. Get a motor manual that comes with an electrical diagram for that car.

What are the colors of 1988 Honda Civic stereo wires?

You can go to this site You got all brand of vehicules and all the years... It was accurate for my 1989 Honda Civic SI. Have a nice day!!! JMoney69

What does a distributor look like on a 1989 Honda Civic dx?

All of the spark plug wires go to the distributor. Just follow the wires and you will see the distributor.

What are the rear right and rear left positive and negative speaker wire colors for a 2008 civic?

The red wire and terminal on a 2008 Honda Civic are the positive wires for the battery. The black wires and terminal is the negative battery cable.

Where are the oxygen sensor and how do you raplace it on a 1997 ford explorer 4.0?

the oxygen sensor or 02 sensor is usually located on you headers it should take a 5/8 wrench it will have two wires coming off of it.