It will be stamped on the case next to the filler plug.
hey how much u put in your oil 98 suzuki 125 2 stroke ?
i have put to much oil in my suzuki gz 125 marauder and need to know how to get it out. Paul Harris
how much oil goes in a 2000 suzuki quadmaster 500
Our Suzuki LT160 is a 1998 and it takes a quart and a half.
Please can you provide me with the type of motor oil used in a Suzuki JR50 and how much do you put in the engine
1 gallon gas 4 ounces oil
type of oil does a suzuki intruder 650 take
it should tell in owners manual
near the oil filler somewhere on the cover it will say how much you need to put in
3.5L half way up the sight glass
2.2 quarts with filter 1.8 without filter change
Normally it is about 4 quarts. Sometimes a little more is required depending on the size of the oil filter used.
Yes, oil should be put in the crankcase on a 1989 Suzuki RM 250. The proper oil to use for this is a product made by Standard Oil called 80-90W Gear Oil.
1.2 qts. US page 31 owner's manual
2.5 qts with out a filter change and 3 qts with on my 2000
Look on the case around the oil fill plug and the amount needed will be stamped on the case.
you put 1400cc of gear oil into the gear box do no trust the fill level screw as the amount of oil was changed under production and you would not have enough oil in it then hope nthis helps you good luck
The amount needed should be stamped on the cases right next to the oil fill plug.
3 quarts then add more if level in window indacates you should do so
Suzuki Manual for a 2006 M50 (VL800) States: 3.6 Quarts with filter change 3.2 Quarts without filter change Use 10W40 SF/SG or SH/SJ motor oil
From my under standing if your riding MOTO, with a fork oil level gauge you measure put 110 mm.
I 'm changing the oil /filter on my John Deer (Riding Mower LA125). How much motor (10w-30) do I put in.
Use of a synthetic oil for the Suzuki DT50 outboard engine oil injection tank is recommended. A high quality 2T oil will provide maximum protection.
It's the plug that is in the middle of a triangular plate. Don't unscrew the other similar-sized bolt because that's what I did and now I don't know which bit to put back first.
just change it take the messure ments for how much to put in drain it and fill it thats what i do with my 06 rm 450
In order to change the motor oil on a Honda XRM 125 you need to lift the bike on a motorcycle rack. You then need to unscrew the drain plug, let the oil drain out, put the drain plug back in, change the oil and put new oil in.
Under the seat there is the tank for the oil, with a cap on saying Motor Oil
Gear oil (80W90 or similar) is used in the transfer case and differentials.
tip the the bike over and let it drain from where u put the oil in
Manual and engineblock sats 1200cc nyt I remember that Suzuki later changed it to 1400cc. I just put 1400cc / 1,4 liter on mine.
as long as they are the same weight you shouldnt have any problems
Best to drain existing oil,measure it then add new trans oil. Better yet, use the right oil, which would be motor oil, not transmission fluid. The amount to use is stamped on the engine case. (850cc)
yes, but you have to rig the water hoses differently. (I put an '89 motor into a '92-same thing) yes, but you have to rig the water hoses differently. (I put an '89 motor into a '92-same thing)
650 cc because on the side of the clutch cover it says 650 cm3 and 1 cm3 = 1 cc.
I'm assuming it hasn't changed too much - I have a 1988 DS 80 and you take off the seat and you will find the oil reservoir there (the little tank with a cap on it) You need to use 2 stroke injector oil that you can get at any bike shop.
It should be stamped on thr right side of the case. If not most 250s require between .75 and .85 liters
how much oil do i put in a xr 200, 2000 model
How much engine oil do you put in a ktm 85
hw much gearbox oil do you put in your ktm 525
I would recommend SAE 10w30 full synthetic.
Drain it and put the right amount back in it, it shoud say on the side cover right near the oil cap
when you put too much oil: engine will lose much power oil push out and make damage your catalic converter
i use 927 mixing oil and i put 4 ounces to the gallon. : )
Remove the plug in the bottom of the oil pan. Allows the oil to drain out of the oil pan. Put the oil pan plug back to its original position. Fill the engine with new oil.
Yes, a person can put to much oil in a car. It usually will not hurt a car, but the excess oil can cause smoking if it gets on the motor.
mayn u put bout wat Eva floats ur boat
generally if it has a separate resvoir you wont need to mix it just simplyuse good grade of 2 cycle oil
32 -1 I find is a great ratio for most bikes not too lean and not to rich. If you wanna run a little leaner go 40 instead of 30
50:1, I usually put 400mL into a 20L jerry can.
motor transfer case axles ? where id guess at motor fill it to the top mark on the dip stick 3.-3/4 on motor. buy 4 qts. be happy.