Best Answer

well first...if the pump is making a loud grinding type noise then maybe all you need id a bearing job....but if the pump needs all depends on the size of the pump and the size of your spa...middle priced pumps go for around 189.00 maybe 230.oo...and having worked on pools and spas for years i'd say go for a jucuzzi brand or a hayward...and as for the light ...if it's a big hayward brand they go for 110.00.....but if you think you can just replace the bulb....good luck

Hmm, Do check and get more recommendations for pumps of better quality.

If your light fixture is more than 8 years old have a new assembly installed.


User Avatar

Wiki User

โˆ™ 2007-09-04 16:52:04
This answer is:
User Avatar
Study guides

Add your answer:

Earn +20 pts
Q: How much should it cost to replace the spa motor with a quieter one and replace the pool light?
Write your answer...
Still have questions?
magnify glass
Related questions

How often a PCV valve should be replaced in a 2000nissan altima?

replace only when u get a check engine light. the valve is good for the life of the motor(should be)

Should you replace both window motor and regulator?


Can you die from drinking motor oil?

How much? The good news is you'll run quieter.

How do you replace a 1970 Pontiac lemans heater motor?

you should be able to unbolt the motor from the firewall on the passenger side of the car

Can you manually close the sunroof on a 2003 chrysler sebring?

Yes, if you remove the dome light you should be able to turn the motor with a screw driver.Yes, if you remove the dome light you should be able to turn the motor with a screw driver.

How do you remove the headlight assembly located on a 1992 Ford Bronco?

If your looking to replace the light bulb then you may have to remove the battery and then there should be a smaller round holister behind the light in the motor capartment all you should have to do is twist it off and then the light bulb should pull right out and then pull the bulb out of the holister (wiring harness) and then put the new one in and then put the holister back in the light assembley (it best not to touch the new light bulbs glass there are extremely fragile). If your going to replace the lense cover there are smaller bolts on the back side of the that you will have to remove to replace the lense, you may also have to remove a couple of bolts on the front by the grill (it can be a pain to replace the lense there is not alot of room to work inside the motor capartment it can be a real knuckle buster).

How do you replace the headlight bulb on a 1995 Ford Probe?

First you need to get a new bulb. Then you need to open the hood. Disconnect the battery terminal (everything you do you should remove the power from the battery) go to the side that has a faulty light and then release the light from the motor this can be done by poping the lift bar from the motor. flip the light up and unscrew the bracing supports to the light bulb.

What is the foot print you need for the motor and can you replace the motor with a standard car motor?

What do you mean footprint? but yes you can replace a motor with a standard car motor.

If the blower stopped working my 2001 Kia Spectra could this be the motor blower resistor or should I replace the blower motor?

Check to see if you are getting power to blower motor - if so replace blower motor If not check fuse, switch, resistor pack.

How do you replace blower motor 78 firebird?

look on the firewall and there should be bolts that come out around the blower motor and then it just pulls out.

When should you replace timing belt on 2005 Honda 3.5 motor?

You do not say the make of vehicle. For an Odyssey, which has that size motor, it should be 105,000 miles or 84 months.

Can you replace a 12v-35w fog light bulb with a 12v-80w?

As long as they are the same volt you should be able to change the wattage, I am assuming this is not on a vehicle in which case you should always check the department for motor vehicles for regulations.

People also asked