answersLogoWhite

0


Best Answer

Roughly 60 in-lbs or a little less. Begin from bolts at middle/center of valve cover and work towards the ends. If you don't have an in-lb torque wrench, then use a nutdriver but tighten it with whichever hand is not your dominant one ( if you're right handed, use your left hand - less likely to ver-tighten.

User Avatar

Wiki User

โˆ™ 2006-04-15 22:25:35
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: How much torque for valve cover bolts on ford focus?
Write your answer...
Submit
Related questions

What are the torque specs for a 94 sc2 valve cover gasket?

89inch pounds is the torque rating for the valve cover bolts


What is the torque and tightening sequence for the valve cover gasket for a 1992 for tempo 4 cylinder?

Torque for valve cover bolts is 7 to 10 ft. Lbs . Tighten the bolts in a criss-cross pattern .


What is torque spec for 2001 altima valve cover?

The 2001 Nissan valve cover bolt torque specification is 45 pounds. The valve cover bolts should be torqued in 15 pound intervals.


What is the manufactured torque spec on a valve cover when tightening the bolts on 2001 FORD expedition?

Tighten the valve cover retaining bolts in sequence, torque them to 71-106 inch lbs. (8-12 Nm).


What are the valve cover torque specs for a 2001 3.0 Mitsubishi Montero Sport?

The 2001 Mitsubishi Montero Sport 3.0 liter engine valve cover torque specification is 40 pounds. You do not want to over torque the valve cover bolts, as you may ruin the valve cover gasket.


What is the valve cover torque spec for a 1998 Hyundai Elantra?

The valve cover bolts need to be torqued to 72 to 84 IN-LBS


What is the torque on valve cover bolts for a 1998 Plymouth neon?

105 in lbs


Torque specs valve cover bolts 1998 accord?

7.2ft lbs


What is the valve cover torque on a 2000 Mazda Protege 1.8L?

The 2000 Mazda 1.8 liter engine valve cover torque specification is 45 pounds. The valve cover bolts should be torqued in 15 pound intervals.


What is torque pressure for the valve cover bolts on a 1998 Hyundai Accent?

72in-lbs


Torque specs for 1999 Hyundai accent's valve cover?

The torque specs on the valve cover bolts on a 1999 Hyundai accent are 71 to 89 INCH pounds or 8-10 N.m.


What are valve cover bolts torque specs for a cavalier 2.2l?

7.2 lbs per Foot


What is the torque on the valve cover gasket bolts?

what kind of car? each car has it own torque spec 2000 Chevy Cavalier


What is the torque setting for valve cover bolts for a 2000 jeep wrangler 4.0?

Valve cover is 85 in-lbs not ft-lbs


Parts diagram for 2001 ford focus wagon?

What is the torque level for the valve cover gasket.


How tight should bolts be so oil wont leak from valve cover?

Check the specs for the vehicle you are working on (You can find them on the net if you do not have the manual) and the torque requirements will be there. Do not over torque the bolts as removing a broken valve cover bolt is a pain. Good luck.


How to replace vlave cover gasket on 1990 Mercury Grand Marquis?

Drain your oil and change your oil filter but do not refill your oil yet. undo the bolts on the valve cover that is leaking and remove the valve cover. remove the old gasket and clean the valve cover. make sure there are no cracks or anything on your valve cover, if so you may need to replace the cover. fit the new gasket on the cover and put the cover back on. now put the bolts back on the valve cover. you will want to google the torquing instructions as well as what order to put the bolts back on. if you over torque you may break your valve cover and it you put the bolts on incorrectly you may not seal your valve cover properly and will still have a leak.


What is the valve cover torque requirements 98 Nissan frontier 2.4?

valve cover torque 98 nissan2.4


93 Jeep Cherokee valve cover torque specs?

the valve cover torque specs are 85in lbs


What is the torque for valve cover bolts on a Ford 5.0 engine?

The valve cover on a Ford 5.0 engine has a torque of 10 foot-pounds, though this can vary between other models. If possible, locate a service manual, which will list the specs for your particular engine.


How do you tighten a valve cover?

There are valve cover bolts around the perimeter of the valve cover. You want these tight but not as tight as you can get them.


Do you need to torque the bolts on the egr valve?

The vehicle manufacturer will quote a torque figure for the EGR valve but in practice most mechanics no not torque them.


How do you replace value cover gasket 2002 ford focus?

ondo valve cover, bolts remove valve cover, remove old gasket from valve cover and block. clean both surfaces well. put gasket glue on one side of gasket and install on cylinder head. align valve cover than replace bolts . tighten in a cross pattern until thet are snug. don't overtighten.


How do you change the valve cover gaskets on a 1981 Ford?

Just did mine on my 300 cu in Ford 1982. Remove any parts that might be in the way, breather, gas line over the valve cover etc. Remove the bolts around the outside of the valve cover. Remove valve cover. Remove old gasket. Clean valve cover. Install new gasket and re-install cover. Replace bolts. Finger tight bolts first then tighten. If you do not have a torque wrench, carefully tighten down bolts alternating from one side to the other tightening them all down evenly. Do not overtighten, they will snap off into the head.


What is the torque level for valve cover gasket on 1989 mercury topaz 2dot3l?

just tighten it snuggly .it will be fine as long as there is all the bolts in it