answersLogoWhite
American Cars
Head Gaskets and Valve Covers
VW New Beetle
Dodge D100

How much torque on head bolts on a 1994 Plymouth Sundance?


Top Answer
User Avatar
Wiki User
Answered 2007-10-27 14:00:36

It is a four step process using torques and a final 1/4 turn of the cyl. head bolt. 45, 65, 65, then 1/4 turn. Check out Alldata.com for a subscription for vehicle information.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Loading...

Still Have Questions?

Related Questions

How do you change the starter on a 1994 Plymouth sundance?

How do I change th starter on a 1994 Plymouth sundance


Where is the camber located on your 1994 Plymouth Sundance?

Front camber is adjusted at the strut to knuckle bolts.


Is there access inside the car to remove the gas tank mounting bolts on a 1994 Plymouth Sundance?

No. It Is Held In Place From The Bottom .


Is a 1994 Plymouth sundance an interference engine?

No, it is not an interference engine.


What if your Plymouth sundance 1994 code reads 3 what does it mean?

The codes on a 1994 Sundance are 2 digit codes. Code 3 is not correct.


Where do I find An oil dipstick for a 1994 Plymouth sundance?

You can purchase a dipstick from the dealer.


Where is the fuse for the heater blower located on a 1994 Plymouth Sundance?

in the fuse box


Where is the oxygen sensor on a 1994 Plymouth sundance?

It is screwed into the exhaust manifold on the rear of the engine.


How do you get at the other end of the bolts that hold the gas tank in place on a 1994 Plymouth Sundance as the end under the car are rusted?

unscrew the screws holding the black metal underneath the back seat, then unscrew the seat belts, the bolts are underneath there.


How do you repair 1994 Plymouth duster speedometer cable?

A 1994 Plymouth Sundance/Duster does not use a speedometer cable. Instead, it uses a Speed Sensor located on the transmission.


Where is the fuel filter located on 1994 Plymouth sundance?

passenger side rear next to fuel tank


1994 ply sundance how do you change front brakes?

Remove the tire and wheel from your 1994 Plymouth Sundance. Remove the brake assembly spring. The brake pads will come off. Reverse the process to install the new brakes.


What type of fuel pump comes with a 1994 Plymouth sundance 2.2L mechanical or electric?

Electrical located in the fuel tank


How do you replace the water pump on 1994 Plymouth Sundance?

It would greatly help to know what engine you have and if it has air conditioning (working or not)


What is torque specs for 1994 4 liter ford explorer intake manifold?

torque specs axel not and wheel hub bolts


Plymouth Sundance 1994 codes 43 55 mean?

Code 43 refers to the coil. Code 55 is end of message.


Where do you install the safety bolt for a child seat in a 1994 Plymouth Sundance?

My child seat car bolt, is in a 1988 Sundance, passenger side about 1 ft from behind back seat, on trunk floor.


Can you show a diagram on how to install a new thermostat in your 1994 2.5 engine Plymouth sundance?

just follow the hose off the radiator that goes into your engine block. its on the front of the motor. you just loosen the 2 bolts that hold the hose on and its right there. very simple


If your flasher stays on like a light but doesn't flash what do you need to do in your Plymouth sundance 1994?

The bulb is falty, replace it and it should cure your problem.


Where is the rev limiter on a 1994 Plymouth sundance?

The engine computer is the rev limiter. It controls max rpm by shutting off fuel and ignition.


How do you remove the gas tank on a 1994 Plymouth Sundance?

My husband And I just changed the tank on our 89 Sundance. Make sure you remove srews from plastic cover piece inside fuel door. Undo the straps from tank. There are also a couple of bolts there to hold tank, close to the back from underneath. THen you have to slide tank over everything there. Not real hard to do.


Are there special bolts on the EGR valve on a 1994 Saturn SC2 The bolts have what appears to be a female torque adaptor of some sort on top of the bolt itself.?

IIRC they are regular bolts.


How much should you torque the head bolts specs on a 1994 cutlas supreme?

33ft.lbs then 90 degrees


Head bolt torque and removal sequence for 1994 Nissan pathfinder?

The 1994 Nissan Pathfinder had bolt torque specification is 140 pounds. There is not any removal sequence. There is only a sequence to put the bolts in.


What are the torque specs for 1994 Chevy 5.7 intake bolts and the fly wheel bolts?

35 ft. lbs. on the intake, and 70 ft. lbs. on the flywheel.