Ford Ranger
Check Engine Light
Toyota Camry
VW Jetta

How ro reset engine check light for highlander 2003?

111213

Top Answer
User Avatar
Wiki User
Answered
2014-10-07 02:13:59
2014-10-07 02:13:59

To reset a check engine light for a Highlander 2003, disconnect the battery for 10 minutes. After this time, reconnect the cables.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


start with engine off. press and hold that speedometer resetter while starting engine, check engine light will flash a few times then disappear.

I have a 2003 Highlander. Whenever I get the oil changed, the check engine light comes on within a couple of days. I finally figured out that there is a hose under the air filter case that gets disconnected when the filter is checked. Just reattach the hose and the light will reset after a few restarts of the engine.

The check engine light is reset with a scan tool after repairing the cause of the fault.The check engine light is reset with a scan tool after repairing the cause of the fault.

The check engine light has to be reset with a OBD scan tool

You reset the check engine light with a scan tool after repairing the failure.

Go call the Toyota car company or headquarters and ask the people who made the car.

how do i reset the check engine light on a 1999 acura 3.2tl

on most vehicles if you disconnect the battery cables it will reset the check engine light

hoe do you reset the check engine light in a 1995 land rover

This is basically an "oil change reminder" light. Check your manual on how to reset it.

The check engine light comes on in a car when there is a problem with the engine. It will go off or be reset when the problem is fixed.

By repairing whatever tripped the light. Then you use an OBD2 scan tool to reset the light. You just have to disconnect the battery for a minute and then the check engine light go off, if the problem has been fixed!!! Disconnecting the battery will reset the light on most, but not all, 1995 & older cars, but on 1996 and newer cars this will rarely reset the light. It requires an OBD2 scan tool to reset the light on most newer cars.

You need a scan tool to properly reset the check engine light.

How do you reset check engine light for the 2009 Chevy trail blazer?

There is no reset button for the check engine light. It must be reset with an OBD scan tool.

The check engine light can be reset two ways. 1) If the problem resolves itself, the check engine light will reset itself after a certain amount of cold starts of the car on the on board computer system. 2) You need an OBD reader that has the reset check engine light capability.

To reset the oil change light on a Toyota Highlander 2012, switch the engine to the OFF position. Then switch the engine back on while pressing the trip meter reset button until it displays 000000 or says COMPLETE.

how do you reset check engine light in 2008 buick lucerne

How do you reset engine light on jeep liberty diesel

The check engine light has nothing to do with an oil change. The check engine light is reset with a scan tool after repairing the failure that caused it.

It is important to make sure the check engine light is not on when having a car inspected. A person can reset the check engine light by clearing the codes that are causing the light to go on.

To reset the check engine light on a 1998 Honda Civic located the blue 15 amp fuse in the engine bay fuse box. The fuse is labeled ECU, and will reset the check engine light when removed.

check engine light reset on a 1999 acura cl 3.0.. Just replaced the egr valve. Thx

No, it may or may not reset the check engine light. If you did not repair the problem that caused the light to come on it will just come back on.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.