Asked in American CarsChevroletKia SportageChevy 350
How tight and in what order do you tighten the head bolts on a Vortex small block 350 V8?
What are the torque specifications for Subaru EJ25 cylinder head bolts?
According to the manual for a EJ25 SOHC: Bolt sequence: ____ | C A F | | E B D | ----- B: INSTALLATION 1) Install the cylinder head and gaskets on cylinder block. CAUTION: • Replace cylinder head gaskets with new ones. • Be careful not to scratch the mating surface of cylinder block and cylinder head. 2) Tighten the cylinder head bolts. (1) Apply a coat of engine oil to the washers and bolt threads. (2) Tighten all bolts to 29 N·m (3.0 kgf-m, 22 ftlb) in alphabetical sequence. (3) Tighten all bolts to 69 N·m (7.0 kgf-m, 51 ftlb) in alphabetical sequence. (4) Back off all bolts in reverse order of assembly by 180° first; back them off by 180° again. (5) Tighten bolts A and B to 34 Nm and bolts C-D-E-F to 15 Nm (6) Tighten all bolts by 90° (7) Tighten all bolts a further 90° CAUTION: Do not tighten bolts more than 90° in total angle
Asked in Dodge Shadow
What is the torque for the head gasket of a '93 dodge shadow and what is the order to tighten the bolts?
What are the cyl. head bolt torque specs for a KIA 1.8 L 2000?
Asked in Pontiac Trans Am
1980 Pontiac transam 5.0 what the order in which you tighten the cylinder bolts?
Asked in Pontiac Sunfire
What is the torque specs for head bolts on a 2000 Pontiac sunfire?
This is right from the good old Hayne's manual. (All numbers are in Ft./Lbs) STEP ONE: Tighten Short bolts - 43 Tighten Long bolts -46 STEP TWO Tighten an addditional 90 degrees Bear in mind that there is a specific tightening order which is just too complicated to explain here. Buy a Haynes manual for more exact instructions FriPilot
Asked in Cars & Vehicles, Head Gaskets and Valve Covers, Toyota Land Cruiser, Timing Belts and Chains
Cylinder head torque settings for a 1997 punto s 60?
Do you have to take apart the rocker arm assembly when replacing head gasket on a 1993 ford explorer?
1986 Nissan PU valve cover gasket. is there a certain order to tighten bolts?
Asked in Ford, Head Gaskets and Valve Covers
What are the torque settings for cylinder head bolts on Ford Bantam 1.3i 2003?
BE SURE TO USE NEW BOLTS AS OLD ONES WILL BE STRETCHED. THEY'RE NOT EXPENSIVE. The torque settings are 40N.m (29.5ft.lb) + 120 degrees for the bigger M11 bolts which secure the main part of the head & 15 N.m (11.06 ft.lb) + 45 degrees for the 2 smaller bolts in the timing chain section. Procedure is as follows: 1) Starting with the middle pair of M11 bolts tighten to 30 N.m working outwards and criss-crossing as you go. 2) Repeating the same order, tighten to 40 N.m 3) Tighten the M8 bolts to 15 N.m 4) Turn the M8 bolts another 45 degrees (I made a paper template to hold next to the bolts) 5) In the same order as before turn the M11 bolts another 60 degrees 6) Turn the M11 bolts another 60 degrees to make total 120 degrees turned.
What are the cylinder head bolt torque settings on a 2001 Jeep Grand Cherokee 4.7L V8 engine?
Torquing the cylinder head bolts is a multistep process in order in ensure that the heads are tightened evenly around the whole head. So: Step one: 11 mm bolts 1 - 10 tighten to 15 ft lbs Step two: 11 mm bolts 1 - 10 tighten to 35 ft lbs Step three: 8 mm bolts 11 - 14 tighten to 18 ft lbs Step four: 11 mm bolts 1 - 10 turn an additional 90 degrees (1/4 turn) Step five: 8 mm bolts 11 - 14 tighten to 22 ft lbs Hope this helps. Good luck !!
Asked in Chevy Malibu, Chevy Aveo
What is cylinder head bolt tightening sequence for a 3.1l Chevy Malibu?
Starting from the left hand side on the back of the head 5328 starting from the left hand side on the front of the head 7146 Tighten the cylinder head bolts to 44 ft.lbs (60 N-m) in the order shown in illustration. Use the J 36660-A torque angle meter in order to rotate the cylinder head bolts an additional 95 degrees. Tighten the bolts in sequence to the the specified torque. With all the bolts tightened, make a second pass tightening all the bolts an additional 95°. Remember, 95° is just a little more than a 1/4 turn, not 1/2 turn, or from 12 o'clock to 3 o'clock on the dial. Do not tighten beyond this specification, otherwise the bolts will be overstressed and the gaskets may suffer damage.
Asked in Toyota Paseo
What is the head bolt torque on a Toyota 5EFE cylinder head for 92-95 paseo?
IN - 8-6-1-3-9 EX - 10-4-2-5-7 The external bolts are longer than the internal bolts. The head bolts are tightened in 2 progressive steps. Apply a light coat of engine oil on the threads and under the heads of the bolts. Torque bolts down (in numerical order) to 33ft-lb Then... Tighten bolts (in numerical order) an extra 90 degrees.
Asked in Auto Parts and Repairs, Fiat Cinquecento
What are the torque settings for the head bolts on a fiat seicento?
Asked in Rover 400 Series
What are the torque setting for the cylinder head bolts on a rover 414 k series?
Asked in Pontiac Sunfire
Whats the torque specs for the flywheel on a 1998 Pontiac sunfire with 2.2 engine?
This is right from the good old Hayne's manual. (All numbers are in Ft./Lbs) STEP ONE: Tighten Short bolts - 43 Tighten Long bolts -46 STEP TWO Tighten an addditional 90 degrees Bear in mind that there is a specific tightening order which is just too complicated to explain here. Buy a Haynes or Chilton manual for more exact instructions
Torque sequence for head gasket buick rendezvous?
hey bud hard to answer this since i cant post a picture but when looking at the head with the flat side on the bottom in order from top left to top right the bolts are as followed 5, 3 , 2 , 8 along the bottom is 7, 1, 4, 6, hope this helps it shows the same for right and left Install the new cylinder head bolts. Tighten Tighten the bolts in the sequence shown to 60 N
Asked in Chevrolet, Head Gaskets and Valve Covers
2.2 Chevy head bolt torque specs?
The head bolts are torque to yield on these engines, meaning that once they have been torqued to specification, they must be replaced when removed. If it is an OHV engine (solid push rods with and internal camshaft and rockers on the head studs) there is a sequence to tightening the head bolts. First, tighten all bolts in a circular motion, starting from the center and working outwards. I prefer to go in a clockwise rotation, but as long as it is in the correct order, rotation is not important. The long bolts must first be tightened to 22 lb/ft and the short ones to 23 lb/ft. Next, in the same order as before, tighten the long bolts to 43 lb/ft and the short bolts to 46 lb/ft. Finally, in the same order as the previous two steps, torque all the bolts an ADDITIONAL 100 degrees (10 degrees past 1/4 turn). A torque angle meter is required to do this properly and to specification. A routine of mine that is not necessary, but I have found helps prevent warping when torquing the head, is when torquing to final spec of 100 degrees, first tighten 60 degrees on all the bolts in the same order as the first two steps, then an additional 40 degrees all around in the same order. Tightening order: 8 4 1 5 9 7 3 2 6 10
what maintenance is required to keep this in working order?
Asked in Chevy Corvette
How do you change a fan belt on a 1974 Corvette?
Loosen the bolts on the alternator or P/S pump, whichever applies, and slide it back enough to loosen the belt. Look and you will see that it can be moved in order to loosen or tighten the belt. Deflection at center point of the belt is approximately 1/2 inch. Loosen the bolts on the alternator or P/S pump, whichever applies, and slide it back enough to loosen the belt. Look and you will see that it can be moved in order to loosen or tighten the belt. Deflection at center point of the belt is approximately 1/2 inch.
What is the torque specs on head gaskets for 1997 Toyota Corolla?