Jeep Comanche
How To

How to check windshield wiper motor in 1992 Jeep Comanche?

697071

Top Answer
User Avatar
Wiki User
Answered
2005-12-07 17:50:30
2005-12-07 17:50:30

I had this same problem First check the fuse. Second check the 4.8 amp circuit breaker at the bottom of the fuse panel (these are common to go out but you have to get them at the dealer and they run about $30.00)Third check the switch with the switch key on wiper switch on take your test light and pierce the coating on the wire if those three thing are good your should get power on your test light no juice the check those three again. Finally take the motor hook it up with jumper wires to the battery, be sure you know which wire is hot when you do this. I dont know what colors are which you could consult a Haynes or Chilton manual for this

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions


Assuming they did not work with the old wiper motor, check the fuse, check the switch.

Check either at the bottom of the windshield washer fluid reservoir or check to see if the wiper motor has washer hoses connected to it

check the wiper fuse. then check the switch, then check the wiper motor

Remove the windshield wiper arm from the windshield wiper motor. Remove the wiring harness. Remove the retaining nut. Reverse the process to install the new windshield wiper motor.

check wiper fuse first, then check wiper switch then check wiper motor

If the wiper motor is good and the motor shaft turns when the wiper is on then you need to check the linkage for the wiper arm. the rear wiper motors and switches are notorious for going bad in the jgc you may have lost your switch.

The windshield wiper motor is located just below the windshield wiper blades and is covered by a black panel.

http://www.ehow.com/video_4936070_install-windshield-wiper-motor.html?pid=1&cp=1 (this is very informative video on how to remove and replace a windshield wiper motor)

# Remove the windshield wiper arms # Remove the cowl cover # Disconnect the electrical connector from the wiper motor # Detach the wiper motor/linkage assembly from the cowl # Remove the wiper motor retaining bolts and remove the motor

* Remove the windshield wiper arms * Remove the cowl cover * Disconnect the electrical connectorr from the wiper motor * Detach the wiper motor/linkage assembly from the cowl * Remove the wiper motor retaining bolts and remove the motor

The windshield wiper motor may have a short in it. The windshield wiper motor may not be grounded properly. Make sure the ground wire is tight and free of corrosion.

The wiper motor is located under the black plastic cowl below the windshield.

# Remove the wiper arms # Remove the windshield wiper cowl cover # Disconnect the electrical connector from the wiper motor and remove the motor # Remove the wiper motor retaining bolts # Pry the linkage arm off the wiper motor pin with large screwdriver

First step would be to check fuse, if good check to see if there is power to the wiper motor, if so bad wiper motor, if not could be switch. Also, get some W-D 40 and spray the area of the windshield wiper motor. Then take a hammer, and gently hit on it. It might just be stuck on something.

A COUPLE OF THINGS TO CHECK 1.Fuse 2.wiper relay 3.power to the wiper motor...if not, check the harness...if yes, check wiper motor. 4.Check the wiper switch on the column YOUR WIPER ARM NUT IS PROBABLY LOOSE. YOU WILL NEED EITHER A 14MM OR A 12MM WRENCH TO TIGHTEN.

Remove the wiring harness from the wiper motor. Remove the windshield wiper arm from the wiper motor. Remove the wiper motor retaining screws. Reverse the process to install the new wiper motor.

The windshield wiper motor is under the front cowl. After removing the cowl the motor should be easily accessed for replacement.

The wiper arm is attached to the pivot which is part of the wiper transmission, which in turn is attached to the wiper motor.

You will have to remove the wiper arms, then remove the cowl, and then the wiper motor.

You have to remove the linkage from the wiper motor.

http://www.ehow.com/video_4936070_install-windshield-wiper-motor.html?pid=1&cp=1 (this is a complete video on how to remove and replace a wiper motor...very informative.)

The wiper motor is mounted on the left inside of the windshield frame on the same bracket as the VIN. Fold down the windshield and is fully accessible.

The windshield wiper control module is usually in the fuse box located in the engine compartment of most automobiles. Sometimes the windshield wiper control module is located on the firewall next to the windshield wiper motor.

The motor sits under the cowl at the base of the wiper arm.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.