0
First, when painting crown molding, you will need to find an out of the way place for painting in. This place must fit the following criteria... * have sufficient square footage to accommodate all of the crown molding laid out flat and allow room for you to safely reach every inch of every stick. (painting crown molding is difficult if you can't reach it) * is totally dry. Do Not let your painted crown molding sit outside over night where it is vulnerable to dew or fog. * is safe from air born dust, dirt, leaves etc. Cover the entire floor space with painters plastic and lay out the crown molding in rows. For easy painting of your crown molding, it's best to group the rows in three to five sticks depending on your arm length. Also it is much easier to paint if they are raised up off the ground. I use buckets and 2x4s to do this. If you crown molding is white already then it is primered, you can skip that step. If not you will need to apply a coat of primer to seal the molding. No need to go very thick with it, one coat will do. Once dry, sand the primer coat lightly.
Applying Paint:
Generously apply the paint to two sticks at a time. Keep the spray nozzle consistently at the same distance from the crown molding (read the instructions on the box for the exact space)
Repeat the process for all the sticks and apply a second coat once dry.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
What type of paint should be used to paint molding?
You can use either water or oil based paint, which are both available in a variety of sheens to paint molding. Water based satin coatings are very popular for crown molding in 2012 and have been for several years, while an oil based semi-gloss are the best choice for baseboards and door moldings where available.
What is better for crown molding paint - latex or enamel?
Water Based Latex Enamel is now available. Easy clean up.
Who is the barefoot painter?
BECAUSE he paint diffrently
What do you call a person who paint walls?
A painter.
Why a painter removes paint from his hand using turpentine?
It depends what kind of "paint " it is.
Can paint for crown molding be a latex satin wall and trim paint?
Yes or it can be the same as the wall paint if it should be flat.
What type of paint should be used to paint molding?
You can use either water or oil based paint, which are both available in a variety of sheens to paint molding. Water based satin coatings are very popular for crown molding in 2012 and have been for several years, while an oil based semi-gloss are the best choice for baseboards and door moldings where available.
What is better for crown molding paint - latex or enamel?
Water Based Latex Enamel is now available. Easy clean up.
How to Create Dramatic Changes Throughout Your Home by Installing Crown Molding?
Crown molding can help to create an elegant and luxurious environment in any room throughout your home. Available in many different styles, from a simple flat design to more sophisticated art deco designs, there are styles of crown molding to create the perfect custom designed look you are looking for.Installing crown molding within your home is something you can do on your own if you have the right tools, materials and a few hours of time to spare. For a fraction of the costs and time that are required to hire professional contractors to create custom designed looks in your home, you can have a unique and appealing space that you can create with your own two hands.Tools and Materials Needed to Install Your Own Crown MoldingWhen you plan on installing crown molding in a room, you will need some basic household tools. This includes a hammer, finishing nails, measuring tape and a miter saw. You can use an air finishing nail gun if you have one available, however, it is not necessary.The materials you will need to have on hand include finishing nails, wood putty and enough crown molding to finish your project. You will also need to have stain, paint, paint brushes and rags available if you are working with unfinished crown molding which you will want to paint when you are done installing. Some safety materials you will need to have includes work gloves and safety glasses.Installing Your Crown Molding throughout Your HomeTo begin, you will need to decide where you want to install your crown molding. Using your measuring tape, you will need to measure the exact amount of molding that will be needed. Use your miter saw to cut any angles that will be used for joining the various corners of the crown molding together. It is important to make sure that you cut these corner angles precise, because if not, there will be noticeable gaps in your corner connections.Using your hammer and finishing nails, secure the crown molding in place. If you are using an air finishing nail gun, hold it flush with the crown molding to prevent the finishing nails from bouncing back and injuring you. Fill in all visible nail holes with your wood putty, making sure that you wipe off the excess putty as necessary. Allow the wood putty to dry for four to six hours.Go over your crown molding with fine grit sandpaper if there are rough spots or areas of wood putty that stand out. You are now ready to paint or sand your crown molding if you are planning on doing so.You will notice the results immediately on the dramatic changes that installing crown molding can be. If you plan on installing crown molding in other areas of your home, you can do so using this same method on almost all rooms.
What is the average cost to have crown molding installed?
, I'm going to talk a little about the cost of crown molding. The average cost of crown molding varies from state to state with the cost of living. When it comes to crown molding most contractors will charge by the linear foot (Linear feet just means any distance or length measured in feet). Some contractors will charge by the corner. When I estimate for crown molding here in Richmond Virginia, I charge by the linear foot. My price for crown molding includes the material cost of the crown molding, and the labor cost of installing the crown molding. You can also get a price for painting the crown molding. If your taking on the job yourself you can purchase the molding at a local Home depot or Lowe's whichever you prefer or you could save yourself about 40 cents/linear foot if you find a local mill work/lumber yard.
Who pays for the paint when you get your bedroom painted does the painter or the employer?
Employer. The painter does the work, you purchase the paint.
Crown Molding Adds Style to a Room?
Crown molding adds style and a finished touch to rooms that need a little help with decor. Crown molding is the topmost molding that is installed where the wall meets the ceiling and adding it can change the look and feel of a room instantly. There are many types of crown molding available in various woods and synthetic materials like Styrofoam and plastic. With new lighter weight materials, installing crown molding is no longer a tedious job for a carpenter and can be a home project that the homeowner can do with some direction and skill. Choosing The Crown Molding Crown molding is available in many different designs and heights, so the style of the room is important. Tips for selecting the right crown molding for the space: * Ceiling height - the lower the ceiling height, the simpler and smaller the molding. Adding a heavy, ornate crown molding to a room with an 8’ ceiling is not a good idea because crown molding will visually lower the ceiling height. Keep it simple and small for low ceilings. Heavy, decorative molding is great for ceiling heights above 10’ that can afford the loss of height. * Room style - coordinate the style and feeling of the room with the style of the crown molding. If the house is extremely modern, a heavy, decorative traditional molding will not blend well with the decor and will visually detract from the simple image and feel of the modern space. * Finish - decide on paint or stain. The finish should coordinate and complement the decor in the room. If stain is better, crown molding is available in a variety of woods such as pine, poplar, oak, maple and cherry. If paint is better, wood or synthetic moldings are appropriate, but the synthetics like foam, Styrofoam or mdf are much lighter, cheaper and easier to install. Making The Purchase * Estimating material - measure around the room on the floor or the wall. Measure each wall length, then total it and add another 10 - 15% for waste. Crown molding comes in precut lengths: wood moldings are usually in 12’ or 16’ lengths; foam moldings are 8’. Example: if all 4 walls (15’ each) total 60’ + 15% waste (addl. 9’) = 69’ needed. If the molding comes in 8’ lengths: 69 divided by 8 = 8.625 pieces - round up to 9 pieces. * Delivery - remember that crown molding comes in precut lengths, the smallest is 8’. Most local companies will allow customer pickups, but if you can’t accommodate the sizes it’s best to schedule a delivery. Most local companies will deliver materials either free or for a nominal charge.
What is a painter?
A painter is a person who creates artworks using paint.
What does an automotive painter do?
they paint
What is the suffix for paint?
The word painter has no prefix. It has one suffix which is the -er.
Can you paint rubbr baseboard molding?
No, it never sticks on.
What is a person who paint pictures?
The person could be known as a painter or as an artist.
