answersLogoWhite
GM and GMC
GMC Jimmy
GMC Sierra
How To

How to program key fob 1998 JIMMY GMC?


Top Answer
User Avatar
Wiki User
Answered 2011-02-14 04:06:32
  1. Close all vehicle doors.
  2. Insert the key into the ignition.
  3. Hold down the power UNLOCK button on the driver's door panel-continue to hold down until instructed to release in step 9.
  4. Perform steps 5 through 8 in fairly rapid succession.
  5. Turn the ignition switch to the ON position (as far as you can go without starting the engine).
  6. Turn the ignition switch to the OFF position.
  7. Turn the ignition switch to the ON position.
  8. Turn the ignition switch to the OFF position.
  9. Release the power unlock button on the door panel. The vehicle will lock and unlock the doors automatically.
  10. Hold down the LOCK and UNLOCK buttons on the transmitter simultaneously until the door locks and unlocks. This step may take up to 30 seconds.
  11. Repeat step 10 NOW for each additional transmitter (including any existing transmitters).
  12. Turn the ignition switch to the ON position in order to exit the transmitter programming mode.

This seems to work on most Jimmys... FYI.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Still Have Questions?

Related Questions

How do you reprogram a key fob for a 1994 gmc jimmy?

the bastards at the dealership have to do it...had it done, not cheap.


Will a Chevrolet key fob work with a GMC?

negative (no)


How do you program a key fob to a 2006 Chevy Malibu?

How do you program a key fob to a 2003 Chevy Malibu


How do you program a 2007 gmc envoy remote?

To program a 2007 GMC Envoy remote, close all the doors. ?æInsert the key in the ignition while holding the unlock button on the drivers side. Turn ignition from on to off twice. ?æNow release the unlock button. ?æThe fob is ready to program.


How do you program a 1995 Lumina APV key fob?

To program any kind of key fob you have to take it to a dealership.


How do you re program key fob for Renault laguna1997?

How do I re program my key fob for renault laguna estate 1997?


How do you program a 2006 gmc sierra key fob?

visit www.programyourremote.com you have to take it to the dealer or a lock smith, becuase the on board programming option was fazed out ofter 2005


How do you program a 2003 deville with a new key fob?

You don't. Take the car and the new fob to a caddy dealer or a locksmith who has the equipment to program it.


How do you program new key fob 2006 Chrysler town and country?

A scan tool is required to program a fob on a 2006 Chrysler Town and Country.


How do you program a Saturn 2001 sc2 keyless entry module?

To add a new key fob, take the vehicle and the key fob to an authorized dealer. To re-program a key fob after replacing it's battery, open the key fob, then read and follow the instructions inside.


How do you program the remote key fob on a 2005 Chevy Malibu maxx with remote start?

How do you program the remote key fob on a 2005 Chevy Malibu maxx


Can you program one key fob for two cars?

It is possible to program one key fob to use on two different cars. If the key fob uses a primitive fixed code system, programming two cars will not work.


How do you program key fob for harley Davidson sportster?

http://www.ehow.com/how_7456283_program-key-fob-harley-davidson.html


How do you program a 2008 Chrysler Key Fob with only one functioning fob?

The dealer scan tool is required.


How can I program my key fob in a 2012 dodge journey?

The key fob programing requires the dealer's scan tool.


How do you program a 1998 Jeep Grand Cherokee alarm to chirp?

I believe you have to take it to a Jeep dealership & they can program it. If you keep pressing the unlock button on your key fob (about four times) it will start chirping. The same for locking.


How do you program 1998 Chevy blazer key FOB?

you hold the lock and unlock buttons at the same time for abought 7 seconds while being near you blazer


How do you reset the fob for a 1998 ford ranger?

turn key from off to run position 8 times quickly (doors will lock/unlock to signal that you're ready to program). Push the unlock button or lock button on the FOB. You should be good to go after that.


How program key fob Ford Contour?

The key FOB allows the user to open the doors of their vehicle when within a given range. This FOB can be programmed by going to the Ford dealership.


How do you program a key fob on a 1999 corvette?

go to corvetteforum.com and they have the answer


How do you program a keyless remote for 2001 Malibu?

You will need a scan tool to program this Keyless Fob.


How do you program a 2001 jeep Cherokee key fob?

You must take it to the dealer to have them program it to your vehicle.


How do you program a new fob for 2002 Jeep Liberty limited if you do not have a fob to program from?

So far its pay the Dealer $68.There got to be a salesman out there who knows and would answer this for a car buyer referal.


How do you program a 2007 gmc key fob?

It's really easy to do! Forget the dealer and search You Tube " GM key fob program". You might want to include the year and model of your car.What could be easier than watching a video to learn something new?Here's one video:http://www.youtube.com/watch?v=sMuW-L6ZwQgAnswerOnly the dealer can do it...Rick D


Key fob 2009 Jeep Wrangler?

Available at the dealer, he will have to program it.Available at the dealer, he will have to program it.


Still have questions?