Spark Plugs and Wires
Timing and Firing Orders
Kia Sephia
How To

How to pull spark plug wires off for a Kia Sephia?

111213

Top Answer
User Avatar
Wiki User
2007-04-12 19:14:22
2007-04-12 19:14:22

Pull the 6 Phillips head screws out of the sparkplug cover on the valve cover. Pull the wire off of the coil starting with the one on the passenger side of the car(#1), this will be the longest wire and will connect to the coil on the far right side of the valve cover(#4)If you are changing the spark plugs, pull the 2 10mm screws out that hold the coil to the cyl.head, just be careful when tightening these back up because if they are too tight you could crack the coilpack. The #2 and #3 plugs are done the same way

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Give the spark plug boot a twist to free it from the spark plug then pull it off of the spark plug by the boot.

User Avatar

You simply pull and twist with force till it comes off. Do not worry about damaging it if you pull straight out.

User Avatar

under the hood usually right on top you should see four black wires in a row. pull of the wire and the spark plug is there. Go to www.kia101.com there is a tutorial on spark plug replacement it's under the tune-up section

User Avatar

The 1988 Chevy Cavalier spark plug wires are quite easy to remove. The spark plug wires simply pull off on each end. Put the new spark light wires on by pushing downward on each end.

User Avatar

follow your plug wires from your distributor,just remember dont pull on the wires to disengage them,pull on the base[CLOSEST TO THE PLUG].

User Avatar

Pull the spark plug wires off the spark plugs. Remove the spark plugs with a spark plug socket. Install the new spark plugs and put the spark plug wires back on. I recomend replacing the spark plug wires as well. If replacing them, just remember that the new wires are hooked up the same ways that the old ones came off.

User Avatar

They are easy to find. Follow the spark plug wires down and pull of the spark plug boot. The plugs are right there.

User Avatar

Removing spark plug wires is rather easy. All a person needs to do is grab the top and the bottom of the cable wires firmly and pull.

User Avatar

pull the plug wires. turn the spark plug counter-clockwise, replace with new plug. replace wire

User Avatar

Under the hood, you should see the rubber spark plug wires. They start at the distributor, they extend out to each cylinder on the motor. Just trace the spark plug wires and at the end is the spark plug. Pull the wire off and there it is. on the engine

User Avatar

It would be wise to replace the wires one at a time so not to mess up the firing order.

User Avatar

Twist boot then pull, this will break the seal from the plug.

User Avatar

right on top of the motor. pull the spark plug wires out and use a 18 mm spark plug socket .and there ya go

User Avatar

Pull them out and replace them one at a time.

User Avatar

First you have to remove the cylinder head cover. You can do this by removing the two hex screws on top. Once those screws are removed, pull the cover off. You will now see a bunch of spark plug wires on top. Pull one of the spark plug wires off, and at the very bottom, you will see your spark plug. Get your Spark Plug Socket, Long Extention, and a rachet and unscrew it and pull out. Once it is out, look at the spark plug for any signs of unusual wear. Get your new spark plug out of the box. Gap that little metal space at the top of the spark plug to what the owners manual says the spark plug gap should be between. Place anti-sieze on the threads of the spark plug and install them in reverse order.It is best to do one spark plug at a time so that you do not mix up the spark plug wires.

User Avatar

Gently twist and pull plug wires off. Turn spark plug counter clockwise with a 5/8 inch spark plug socket and a ratchet.

User Avatar

Pull them off of the spark plugs and distributer cap. . .

User Avatar

Switch off the car and then pull out the spark plug wires by holding them from the plug boot. Remove the spark plugs using a socket wrench and clean off any dirt or debris that is left in the spark plug hole. Replace the plug and tighten them first by hand and then by wrench. Reattach the wires.

User Avatar

The Escape uses Coil Over Plug technology. There is a coil for each cylinder, thus eliminating the need for spark plug wires. To access the spark plug, you need to remove the 2 bolts on the coil and pull it out.

User Avatar

they are dropped down inside the valve cover. pull the plug wires and use a plug socket and extension to reach them.

User Avatar

The 2.4 Liter Mitsu engine is a hemi--the spark plugs are located in the center of the valve cover. If you pull one of the spark plug wires up and out, you will see that it has about a 5 inch extension that goes down to the plug. Then you can put a spark plug socket on a long extension and stick it down into the hole and remove the plug. It also has 2 "coils" that are in line on the wires, so it costs about $200 to replace the wires.

User Avatar

If you mean that the wire came out of the boot, then pull the boot off of the spark plug and use a spark plug socket to remove the spark plug.

User Avatar

To change the spark plugs in a Chevy Celebrity: 1. Give the spark plug boot a twist to free it up from the spark plug, then pull on the boot to remove the spark plug wire from the spark plug. 2. Use a 5/8" spark plug socket with an extension and ratchet or breaker bar to loosen then remove the spark plug. 3. Set the gap on the new plug to .045" then screw it back into the spark plug hole in the head. Tighten the spark plug and replace the spark plug wire. I change the spark plugs one at a time to keep from getting the spark plug wires on the wrong spark plug.

User Avatar

No, they don't necessarily have to be replaced. However it is usually a good idea to replace the wires along with the spark plugs. As the wires age and go through heating cooling cycles they get stiff and brittle. As you flex the wires to remove them from the spark plugs the inner conductor often breaks causing a misfire. Also when you pull the spark plug boots off of the spark plugs the connector often can break loose and stay on the spark plug, thus ruining the wire.

User Avatar

Do this one plug at a time, and reconnect that wire so as to not get wires mixed up. REMOVAL Remove spark plug wires from spark plugs with a Spark Plug Wire Remover tool, pull outward on the boot with a slight side-to-side twist. Loosen spark plugs and remove any dirt or foreign material from spark plug areas of cylinder head with compressed air. Remove spark plugs. INSTALLATION Inspect and adjust spark plugs. Spark Plug Gap: 0.042" to 0.046". Install spark plugs. Tighten spark plugs to 9-20 N.m (7-15 lb in). Connect spark plug wires to spark plugs.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.