answersLogoWhite

0


Best Answer

93 goes like this: remove plastic cover. remove key/lock module (need tamper proof torques tips. To get to the guts you need to drill out hollow rivets. To replace you need to ? (I drilled new holes then pilot holes in the plastic so i could install screws ... counter sunk to keep case flush) The key activates parts that are made of pot metal and break if forced. I drilled and inserted a drive pin to replace the front edge of the contact surface which was broken off.

good luck

User Avatar

Wiki User

โˆ™ 2011-01-12 01:04:37
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: How to remove an ignition cylinder on a 92 Jeep Cherokee?
Write your answer...
Submit
Related questions

How do you remove the ignition cylinder from a 1999 Jeep Cherokee with no key?

You will have to drill the center out to get it to turn.


Need removal and installation instructions for an ignition cylinder 2000 Grand Cherokee Jeep?

Need removal and installation instructions for an ignition lock cylinder -- 1999 Grand Cherokee Limited?


Wiring diagram ignition 99 Jeep Cherokee?

1993 Jeep Cherokee Ignition Wiring ...


How do you replace lifters on 1998 Jeep Cherokee with a 4.0l 6 cylinder?

You have to remove the cylinder head to access lifters.


Does a 97 Jeep Grand Cherokee 8 cylinder have an ignition coil?

Yes, it is on the front passenger side corner of the engine.


How do you remove the ignition switch key lock on a 1988 Jeep Cherokee?

Remove steering wheel, turn signal (4 screws), and torx holding ignition, reverse to reinstall.


How do you change lifters on a 1995 jeep cherokee Laredo?

You have to remove the cylinder head(s) to access the lifters.You have to remove the cylinder head(s) to access the lifters.


How do i identify the transmission in my 1999 jeep Cherokee Laredo?

A Jeep Cherokee had a AW 4. A six cylinder Grand Cherokee had a 42 re. An eight cylinder had a 45rfe.


How do you change ignition switch on Jeep Cherokee Laredo?

necesito ignition switch on jeep Cherokee Laredo 1996 mi correo es skyrouse@hotmail.com


What kind of freon 1998 Jeep Cherokee has 6 cylinder?

A 1998 Jeep Cherokee uses R134a.


What would be the cause of having to turn the ignition key to an extreme before your 1996 jeep grand Cherokee Laredo will start?

The back of the ignition key cylinder is probably broken.


How many coil packs does a 97 jeep grand Cherokee have?

A 1997 Jeep Grand Cherokee has one ignition coil.


Where is the block heater on 2000 Jeep Grand Cherokee 6 cylinder?

where is engine block heater on 2000 jeep grand cherokee 6 cylinder engine?


Where is the ignition fuse on a 96 Jeep Grand Cherokee?

The ignition fuse on a \'96 Jeep Grand Cherokee is in the fuse box It is usually located on the passenger side on the corner of the dash.


99 Jeep Cherokee Laredo stay running after turn off the ignition switch?

99 jeep Cherokee Laredo stay running after turn off the ignition switch?


How do you remove the ignition key that is stuck in a 1996 Jeep Cherokee Sport?

put it into park, i made the same mistake and couldn't get it out for ages!


How do you remove the ignition switch in a 1999 Jeep Grand Cherokee Laredo?

you take it to the dealer caz you cant do it for sure its incredably complicated


Why is there no spark in a 1991 Jeep Cherokee?

Replace the ignition coil.


Will a 2000 jeep wrangler 6-cylinder fit a 1999 jeep grand Cherokee 6-cylinder?

The blocks are the same.


How do you replace the key cylinder on a Jeep Cherokee?

1. Remove the lower steering wheel shroud. For a 1998 Jeep Cherokee it is connected with three #2 Phillips screws underneath. 2. Put the key in the ignition, turn the ignition to ON. On the key cylender, in the middle bottom, is a rectangular button. Press it all the way in, with a small bladed standard screwdriver. 3. Pull the key cylender out. Reverse steps to reinstall.


Is the door and the ignition key the same for a 97 Jeep Grand Cherokee?

I have a 1997 Grand Cherokee, and my key fits both the door and the ignition.


Is changing push rods and tappets on Jeep CHEROKEE 4.0 difficult?

Yes, to access the tappets(lifters) you have to remove the cylinder head.


Where is the ignition coil on a Jeep Cherokee?

Engine compartment ne'er the the distributer


Why would an ignition coil burn out on a 2001 jeep Cherokee?

It could.


Where is the ballast resistor for a 1994 Jeep Cherokee?

It does not have an ignition ballast resistor.It does not have an ignition ballast resistor.