answersLogoWhite
Starters and Ignition Systems
Dodge Caravan
Dodge Grand Caravan
How To

How to remove and install a starter for a 2000 dod gr caravan se?

456

Top Answer
User Avatar
Wiki User
2010-03-06 16:00:30
2010-03-06 16:00:30

how to remove a starter on 2000 dodge caravan

1

Related Questions

User Avatar

Disconnec battery Starter is located under car where engine meets tranny, remove the electric connectors Remove starter mounting bolts Install new starter in reverse order of removal

User Avatar

To install a 2000 Yamaha Waverunner XL 1200 starter, first remove the 2 bolts. Then the wires connected to the starter. Remove the starter and replace with new.

User Avatar

Remove the positive battery cable from your 2000 Chevy Malibu battery. Remove the cables from the front of the starter. Remove the starter retaining bolts. Reverse the process to install your new starter.

User Avatar

As long as the engines are the same, most parts from years 1996-2000 are interchangeable.

User Avatar

how do i install a aftermarket radio in a dodge caravan

User Avatar

Remove the positive battery cable from your 2000 Saturn battery. Remove the cables from the front of the starter. Remove the three starter retaining bolts. Reverse the process to install the new starter.

User Avatar

The 2000 Dodge Caravan alternator can be changed by removing the alternator belt. Remove the wiring harness from the back of the alternator. Loosen and remove the alternator retaining bolts. Install the new alternator by reversing the process.

User Avatar

You remove the ac compressor and install a pulley bypass kit from a part store.You remove the ac compressor and install a pulley bypass kit from a part store.

User Avatar

Front of the block, behind the motor mount.

User Avatar

jack up vehicle and support it with stands.the starter is on the front of the engine,there are two bolts that hold the starter up.you will need a 15mm socket to remove the bolts. you will also need a 13mm socket to remove the power wire off the back of the starter.then there is one more wire you will need to remove and its an 8mm.just do the reverse to install it

User Avatar

I'm assuming you mean how do you remove a starter in a 2000 Gran Marquis? 1. Disconnect the battery ground cable. 2. Raise and support the vehicle. 3. Remove the starter motor solenoid terminal cover. 4. Remove the bolt and position the transmission cooler lines and bracket out of the way. 5. Remove the red protective cap on the starter solenoid. 6. Remove the nut and disconnect the wire. 7. Remove the nut and disconnect the wire. 8. Remove the three bolts. 9. Remove the starter motor .

User Avatar

Disconnect battery. Raise and properly support front of vehicle. Locate starter which is located under car where engine and tranny connect. Remove nuts that secure wires to starter. Remove move bolts securing starter. Install new starter in reverse order of removal.

User Avatar

For the 3.0 liter engine. Disconnect negative battery terminal. Locate starter at lower front of engine by engine fans. 2 bolts holding starter in, upper and lower. Remove lower bolt 3/4 way- easy to see, upper bolt go from top of engine to remove (need extensions). Completely remove lower bolt and remove positive battery connector and signal wire on top of starter. Install reverse of removal.

User Avatar

The solenoid on this model is part of the starter motor, mounted directly on top of it.

User Avatar

it is behind the starter. You will have to remove the starter to get to it.

User Avatar

To get to the starter you must remove the upper intake manifold first.

User Avatar

# Disconnect the remote battery negative cable from the terminal on shock tower # Remove air cleaner resonator. # Remove the battery positive cable nut from starter. Remove battery positive cable and generator output wire from starter # Disconnect push on solenoid connector. Unlock the red locking tab and compress lock to release the connector. # Remove two bolts attaching starter to transmission housing and remove starter from vehicle. # Reverse steps to install.

User Avatar

Disconnect the - battery cable Raise and support vehicle Disconnect wiring harness at the top of starter Remove starter mounting bolts Twist starter to remove

User Avatar

With the right tools and knowledge, no.

User Avatar

como se desactiva una alarma de caravan 96

User Avatar

anyone in there right mind would not to remove breaks on a car. Really!!

User Avatar

Remove your battery. Remove the battery tray. Remove the air filter housing and air intake duct. Remove the starter motor mounting bolts. Pull the starter away from the engine a bit. Detach the electrical connector from the starter solenoid. Remove the nut and disconnect the battery starter cable. Remove the starter and put in your new one.

User Avatar

2.0L Engine Fig. 1: Remove the three starter mounting bolts Fig. 2: Carefully lower the starter out of the vehicle # Disconnect the negative battery cable. # Remove air intake resonators. # Remove starter motor upper mounting bolts. # Raise and support the vehicle. # Remove the nuts on the starter terminals and remove the cables from the terminals. # Remove the two starter lower retaining bolts and remove the starter. To install: # Place the starter into position and tighten the 2 lower retaining bolts to 15-20 ft. lbs (20-27 Nm). # Place the starter cables onto the terminals and tighten the retaining nuts to 80-124 inch lbs. (5-7 Nm). # Lower the vehicle. # Install and tighten the upper retaining bolt to 15-20 ft. lbs (20-27 Nm). # Install the air intake resonators. # Connect the negative battery cable. 2.5L Engine Fig. 3: Starter mounting - 2.5L engine # Disconnect the negative battery cable. # Remove the engine air cleaner assembly. # Remove the fuel feed and return lines from the support bracket located on the accelerator cable bracket, and remove the fuel line bracket. # On vehicles equipped with a automatic transaxle, remove the gear selector and the gear shift cable bracket from the transaxle. # Remove the air cleaner support bracket from the engine and transaxle mount. # Remove the nuts on the starter terminals and remove the cables from the terminals. # Remove the starter motor-to-transaxle case retaining bolt at the rear of the starter. # Remove the two starter retaining bolts and carefully lift the starter from the transaxle case while disengaging the alignment pins. To install: # Position the starter onto the alignment pins and onto the transaxle case. # Install the two starter retaining bolts and the rear retaining bolt and tighten them to 15-21 ft. lbs. (21-29 Nm). # Place the starter cables onto the terminals and tighten the retaining nuts to 80-124 inch lbs. (5-7 Nm). # Install the air cleaner support bracket. # If removed, install the gear shift selector and bracket. # Install the fuel line bracket and install the fuel lines in the bracket. # Install the air cleaner assembly. # Connect the negative battery cable. Reference http://www.freeautomechanic.com

User Avatar

You will have to remove starter, It is behind the starter in the block.

User Avatar

It is behind the starter, Will need to remove starter to service it.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.