Heater Cores and Blower Fans
Mercury Tracer
How To

How to remove heater core from 1994 mercury tracer?

181920

Top Answer
User Avatar
Wiki User
2006-04-12 12:44:45
2006-04-12 12:44:45

The dash must be completely removed in order to gain access to the heater box. Then the heater hoses are disconnected and the heater box is removed and opened up. That gains access to the heater core for relacement.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The engine oil pan is bolted to the bottom of the engine on your 1994 Mercury Tracer

User Avatar

You can't. Computer sets it. Chuck the Tracer pro.

User Avatar

Begin by removing the break assembly from your 1994 Mercury. Tap on the rear brake drums with a hammer or mallet. The brake drums will become loose and will simply slide off.

User Avatar

You have to remove the dash and cowling underhood to remove the heater case. Then you would need to disassemble the heater case.

User Avatar

According to one of Ford's websites : For the 1.9 liter four cylinder engine in a 1994 Mercury Tracer : ( the spark plug gap is .054 inch )

User Avatar

Follow the plug wires and they will go to the distributor cap.

User Avatar

Should be a plug at the side of the transmission- fill to this level

User Avatar

in the 1.9 liter engine it should be from 35-45 psi

User Avatar

On your 1994 MERCURY TRACER, the THERMOSTAT is: UNDER HOOD, DRIVER SIDE, UPPER ENGINE AREA, ENGINE END OF UPPER RADIATOR HOSE, MOUNTED IN COOLANT OUTLET HOUSING. The upper radiator hose will lead you to the thermostat housing as described above. It is much easier to access if you remove the distributor which sits above the thermostat. Mark your plug wires if you unplug them.

User Avatar

I do not know, but I am having the same problems with the removal of my 1994 tracer's stereo

User Avatar

4 bolts are romoved from the backsode of the steering wheel. If airbag equipped remove airbag fuse first. Then remove airbag/ horn/ center assembly. Remove large nut from center of wheel, then pull wheel with steering wheel puller.

User Avatar

Drain the water from your 1994 Chevrolet Blazer cooling system. Remove the heater core water supply hoses. Remove the heater core retaining bolts. Reverse the process to install the new heater core.

User Avatar

you have to take out the whole dashboard

User Avatar

Remove the wiring harness from the back of your 1994 Chevy heater fan motor. Remove the heater fan motor retaining bolts. Remove the fan from the front of the heater motor. Reverse the process to install the new heater fan motor.

User Avatar

To the right of the fusebox under dash by your left knee is a 30A circuitbreaker, push the red button in.

User Avatar

Remove the tire and wheel from your 1994 Mercury Cougar. Remove the brake spring and brake caliper. The brake shoes will come off.

User Avatar

The throttle position sensor (TPS) on a 1994 Mercury Tracer is located towards the driver's side of vehicle, under the hood. Directly to the left of the battery will be an intake air hose with a metal screw-on clamp. This clamp attaches the air hose to the engine's intake manifold. To the left of the clamp with the be the engines TPS assembly.

User Avatar

Drain the water from your 1994 Chevrolet Cavalier cooling system. Remove the water supply hoses from the heater core. Remove the heater core retaining bolts. Reverse the process to install your new heater core.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.