Cadillac Fleetwood
Toyota 4Runner
Ford Bronco II
1995-2005 Chevy Cavaliers
How To

How to remove ignition key cylinder on a 1993 fleetwood brougham?

585960

Top Answer
User Avatar
Wiki User
2005-10-15 03:10:42
2005-10-15 03:10:42

First I'll say is that if you are not a well seasoned tech, not an easy task to perform. Basically its positioned right below the signal switch. So if you can reach down that far into the steering column, there it is. Depress the locking plate and remove.

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Remove the ignition cylinder retaining ring. Poll the ignition cylinder out. Remove the wiring harness from the back of the ignition cylinder.

User Avatar

You will need to remove the retaining ring at the top of your 2003 Kia ignition cylinder. The ignition cylinder will slide out. Remove the wiring harness from the back of the ignition cylinder.

User Avatar

You will need to remove the retaining ring from the top of your 1975 Chevrolet pickup truck ignition cylinder. Slide the ignition cylinder out and remove the wiring harness. Reverse the process to install the new ignition cylinder.

User Avatar

Remove the retaining ring from the top of your 2000 Mercedes-Benz ignition lock cylinder. Slide the ignition lock cylinder out and remove the wiring harness.

User Avatar

Remove the retaining ring, from the top of your 1997 Ford Astro ignition lock cylinder. Remove the wiring harness from the back of the ignition lock cylinder.

User Avatar

Remove the retaining ring from the top of your 1997 Chevrolet 1500 ignition cylinder. Slide the ignition cylinder out and remove the wiring harness.

User Avatar

You can change the ignition cylinder on your 1999 Mercury Mystique by removing the retaining ring at the top of the ignition cylinder. The ignition cylinder will slide out. Remove the wiring harness.

User Avatar

Remove the retaining ring at the top of your Chevy S 10 ignition lock cylinder. Slide the ignition lock cylinder out. Remove the wiring harness from the back of the ignition lock cylinder. Reverse the process to install the new ignition lock cylinder.

User Avatar

Begin by removing the retaining ring at the top of your 1994 Ford ignition lock cylinder. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the ignition lock cylinder. Reverse the process to install your new ignition lock cylinder.

User Avatar

Remove the retaining ring at the top of your 1991 Acura Legend ignition switch. The ignition switch cylinder will slide out. Remove the wiring harness from the end of the ignition cylinder. Reverse the process to install your new ignition switch cylinder.

User Avatar

The 1994 Pontiac Grand Am ignition lock cylinder is held in place by the retaining ring at the top of the cylinder. Remove the retaining ring. Remove the wiring harness from the back of the cylinder.

User Avatar

To remove the ignition cylinder on a 2000 Lexus RX300, first remove the vanity engine cover by unscrewing it. Disconnect the wiring connector by pushing the clip that holds it in place. Finally, remove the bolts that hold the ignition cylinder.

User Avatar

You can remove the 2000 Chevrolet Astro Van the ignition switch cylinder by removing the retaining ring. The retaining ring will need to be turned to the left. The ignition switch cylinder will slide out.

User Avatar

You can replace the ignition lock cylinder in your 1994 Pontiac Firebird without removing the steering will. Remove the retaining ring at the top of the ignition cylinder. The ignition cylinder will slide out.

User Avatar

Ignition switch and lock cylinder removal 1988 Dodge Ram 50.Disconnect the negative battery cable from the battery.Remove the steering column cover to gain access to the ignition switch/lock cylinder.Using wire cutters, remove the cable band.Remove the bolts that hold the ignition switch/lock cylinder to the steering column.Unbolt and remove the key reminder switch and remove the switch lock cylinder from the steering column.

User Avatar

how DO YOU REMOVE AN IGNITION CYLINDER FROM A MALIBU CHEVROLET 2000

User Avatar

To change the ignition lock cylinder in a 2001 Chevrolet Tracker, first disarm the air bag system. Then remove the clock spring assembly to be able to remove the old ignition lock cylinder and replace with a new.

User Avatar

Begin by removing the retaining ring at the top of your 1996 Mercury Tracer ignition switch. The ignition lock cylinder will slide out. Remove the wiring harness from the end of the cylinder. Reverse the process to install your new ignition lock cylinder.

User Avatar

Begin by removing the retaining ring at the top of your 1996 Chevrolet Silverado ignition lock cylinder. Slide the ignition lock out and remove the wiring harness. Reverse the process to install your new ignition lock cylinder.

User Avatar

Insert the key into the ignition. Push the release/switch button at the bottom of the cylinder, and pull the cylinder out.?รฆ

User Avatar

There is an access cover just under the ignition cylinder. Remove this to remove the stuck key.

User Avatar

if it is the ignition lock cylinder, first disconnect the battery, you need to remove the steering wheel ,turn signal switch , etc, then you need to insert the ignition key into the lock cylinder, turn it to the run position,then pull the cylinder out, reverse the operation to install the cylinder,

User Avatar

what lock cylinder?door or ignition? door is simple, remove inner door panel, unhook rods attached to lock cylinder, remove retaining clip

User Avatar

key switch tumbler removal on 1998 astro


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.