Chevy Blazer
Chevy Silverado
Chevy Suburban
Chevy Trucks and SUVs
How To

How to remove latch on 79 blazer glove box?

141516

Top Answer
User Avatar
Wiki User
Answered
2011-09-13 05:43:47
2011-09-13 05:43:47

Pry the knob off and remove threaded lock ring for 79 blazer as well all 79 Chevy truck without locking latch.

001
๐Ÿ˜‚
0
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Related Questions


The 1979 Chevy Silverado glove box latch is held in place with two retaining screws. Remove the retaining screws and the glove box latch will come off.


Replace any broken parts or adjust latch assembly


Remove the three Philips screws along the top and the two on the bottom corners and remove the entire glove box. You can then work on the latch from the back of the latch and easily open the glove compartment by gently prying off the corners of the glove box from the locking pins.


To remove the glove box on a Chevy Celebrity pull the glove box out, then push up on the tab on the underside of the box to release the latch that keeps the globe box in. It will then simply pull the rest of the way out.


Open the glove box, unscrew the three screws next to the lock, tap lightly and it will come out.


Open the glove box and you should see a single screw on the back of the latch. Simply unscrew this and the latch should come out.


2000 Protege did not have a key-lock glove box. Pull the glove box release handle all the way open, then keep pulling it till it snaps off. Behind where the handle pivot point was is an opening to the inside of the latch mechanism. Stick a thin tool in the rectangular opening and push the latch bolt down to release the glove box. Once open, remove the 3 screws that attach the latch to the glove box, and head to your nearest junk-yard for a replacement latch.


Remove you glove box. It should be behind it.



Not all 66 Mustangs had a locking glove box; some came with a standard glove box latch and others with the locking latch. C5ZZ-6506072-B : 65 Glove Box Latch Pony (66 All) C5ZZ-6506072-BL : 65 Glove Box Lock Pony (66 All) Source : http://www.aapd.net


how to remove glove box in 1993 camry


Remove it by depressing the retainer tab then sliding the knob out of its latch case. Alternatively, you can use a flat screw driver to insert it behind the knob to force it out.


Look up under the handle and there's a hole perpendicular to the front of the glove box. Insert a small screw driver about an inch into the hole and pry gently towards the back of the truck which should release the glove box. It takes some encouragement, but remove the 2 screws holding the latch (from the inside of the glove box) and the latch should come free out the front.


Assuming it's the same as a 94 C1500, Open the glove-box, remove the screws across the top and bottom, remove the cables that support the glove-box door, remove the glove box door, remove the glove box compartment. I have a 95 K1500, you just have to squeeze the top of the glove box, clear the mount and then remove the plastic strap on the left side, and then open the glove box fully it just fall down, no need to unscrew anything.


All you have to do is, When the glove box is open just open it again when it's closed. hope this helps.


You can open the Honda Accord jammed glove box by gently prying on the glove box door with a flat head screwdriver. Pry on the door just above the latch.


Open the glove box, squeeze the sides in and remove the glove box (easy to re-install). Behind you will see a long horizontal rectangular hatch. Depress the plastic latch and remove the hatch. Remove old filter, clean out any loose debris, replace with new filter. Put the hatch and glove box back in and you are done.


If the plastic part is broken, it can not be repaired. New latch is about $ 50.00.


There are 2 screws on the inside that get removed and pull the latch down.


the button ,for the latch is in glove box on left hand side


I need to remove my glove box on my 2009 Nissan Murano. Where are the glove box pins located?


It is very easy to repair a broken glove box latch. Once you've acquired the part, you will need to take the inner and outer panels of the door apart. The latch is attached to the outer panel of the door. It can be removed with a couple of screws.


if there is not a key hole you cannot lock it.


The ECM on a 1992 S10 Blazer is located below the glove box.


It will be inside the glove box to the right. You will have to remove the glove box.



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.