answersLogoWhite
Geo Storm
VW New Beetle
Ford Expedition Eddie Bauer
Ford F-350
How To

How to remove starter motor?

678

Top Answer
User Avatar
Wiki User
2014-10-07 02:13:24
2014-10-07 02:13:24

To remove the starter motor, disconnect the battery first. Take a picture, if possible, so that the new starter can be put back in place the same as the old one was. Disconnect the wires and remove the starter bolts. Remove the starter and replace with a new one. Hook up the wires and the battery.

1

Related Questions

User Avatar

how do i remove the starter motor Mazda rx8

User Avatar

how to remove starter motor on bmw 745

User Avatar

how to remove starter motor for Peugeot 206 1.4 hdi.

User Avatar

How do i remove an Audi A6 Starter motor

User Avatar

remove elec cables on front of starter/m then remove two bolts from face of starter/m then remove

User Avatar

Remove the motor. Lifting the motor six inches will give access to the starter

User Avatar

Begin by removing the positive cable from your 1990 Volvo 240 battery. Remove the cables from the front of the starter motor. Remove the starter motor retaining bolts. Reverse the process to install your new starter motor.

User Avatar

disconnect battery. from underneath disconnect solenoid wire and battery cable from starter solenoid. remove starter motor bolts. remove starter motor. installation is the reverse but be sure to place the starter shim between the starter motor and the engine or you will get noise during starts.

User Avatar

Disconnect the battery. Remove the H.D cable and starter solenoid wire from the starter motor, remove the bolts from underneath, remove the starter. BigBronco351

User Avatar

# Disconnect the negative battery cable # Remove the air intake duct and the air cleaner assembly # Disconnect the speedometer cable from the transaxle # Unscrew the nut and disconnect the battery cable from the starter motor then disconnect the wiring from the solenoid # Remove the starter motor mounting bolts,supporting the starter motor as the bolts are removed and remove the starter motor

User Avatar

# Disconnect the negative battery cable # Remove the air intake duct and the air cleaner assembly # Disconnect the speedometer cable from the transaxle # Unscrew the nut and disconnect the battery cable from the starter motor then disconnect the wiring from the solenoid # Remove the starter motor mounting bolts,supporting the starter motor as the bolts are removed and remove the starter motor

User Avatar

With motor off unplug the battery. Then remove the wires from the starter. Undo the 2 bolts holding the starter in place and remove. Reverse procedure for installation.

User Avatar

You will need to loosen the motor mount on the side of the starter to jack up the motor slightly to remove the starter after removing the bolts that hold the starter on to the engine. Remove all wires from starter also.

User Avatar

here are the steps to remove your starterDisarm radio coded theft protection as outlined in Technician Safety Information .Disconnect battery ground cable.Raise and support vehicle.Disconnect starter motor electrical connectors.Remove starter motor bolts and starter motor from vehicle.Reverse procedure to install, noting the following:Torque starter motor attaching bolts to 28 - 38 ft.lb.

User Avatar

Disconnect the - battery cable Raise and support vehicle Disconect wiring harness at top of starter Remove starter mounting bolts Remove starter

User Avatar

I just removed a 1.7 Diesel starter motor. ALLWAYS DISCONNECT BATTERY NEGATIVE TERMINAL (10 mm) Remove top half of inlet manifold (8mm 12sided socket or spanner) Undo the two plastic bolts on the expansion tank (water bottle. 10mm) Move tank out the way Look down onto starter motor; remove bolt on which goes through bell housing into starter motor (16mm ) Jack car up; from underneath look up to starter motor, remove bolt which goes through the starter into gearbox (15mm) Remove nut from starter solenoid (little part of starter motor. 13 mm) Undo Philips bolt and disconnect wire You have removed your starter motor

User Avatar

To change the starter on a 1998 s10, the motor mount will have to be removed. Support the motor on a jack with a board on the top of it, and remove the mount to get to the starter.

User Avatar

Remove the positive battery cable from your 1997 Dodge Grand Caravan battery. Remove the cables from the starter. Remove the retaining bolts from the starter. The starter will come off.

User Avatar

# Disconnect negative battery cable # Raise and support the truck # Remove the protective cover from the starter motor solenoid terminals # Disconnect the wiring from the terminals on the starter motor solenoid # Remove the starter mounting bolts and detach the starter from the engine

User Avatar

To remove the starter from a ford transit van, first you need to disconnect the battery. Once the battery is disconnected, you will find the starter on the gearbox facing the flywheel. At this point, you will need to remove connectors that are located on the back of the starter, and take out the bolts that hold it in place. By giving the starter a shake, the starter motor should come out.

User Avatar

Some vehicles require the motor mount (on the side the starter is on) to be loosened or even removed in order to jack up the motor to remove and replace the starter.

User Avatar

On the passenger side and they are a prick to remove

User Avatar

remove 13 mm nut connecting positive to starter motor, unclip smaller wire next to it, remove the three (3) bolts attaching starter motor to engine housing...that's how i just removed mine 5 minutes ago

User Avatar

disconnect the negative side of the battery. raise car and from underneath, disconnect the solenoid wire and battery cabble from the starter motor solenoid,remove the 2 starter motor boltsremove the starter and note the position of the starter shim if equipped. some cars don't have it. installation is the reverse.

User Avatar

The starter motor on a Citrogen Berlingo can be changed by first removing the electrical wires. Remove the three bolts that hold the starter in place. The starter will come out. Reverse the process to install the new starter.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.