Cars & Vehicles
Starters and Ignition Systems
Chevy Silverado
Chevy Trucks and SUVs
How To

How to replace 1996 1500 Chevy truck ignition switch?

394041

Top Answer
User Avatar
Wiki User
2005-09-11 02:37:44
2005-09-11 02:37:44

if tis like a 1995 you need to remove the lower dash panel below the column, the culoumn sleeve that is held on by 2 torx scres from the bottom, then you need a inverted torx sicket to remove to that hold the top sleeve on the column then you can get to the ignition switch

123
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

replace ighnition switch for 1985 chevlot

User Avatar

With no key you will have to drill out the existing tumbler assembly from the switch in order to unscrew the ignition switch bezel.

User Avatar

n ignition switch on a 1991 Chevrolet astro vanAnswern ignition switch on a 1991 Chevrolet astro van

User Avatar

how do you replace3 dimmer switch 1987 chevy silverado 4 x 4

User Avatar

1995 ford 350 1 ton box truck ignition replacement

User Avatar

can a chevy truck with a 350 engine with a tbi cause detonation and pre- ignition?

User Avatar

A bad ignition switch can shut down a vehicle's electrical system. Ignition switches have been the cause of a major recall by General Motors.

User Avatar

how to remove cover to replace ignition lock cylinder and what type of tools do i need

User Avatar

It is easy . Go to auto parts store buy the ignition switch since directions are in the box. You will need one piece that you can make to hold the springs in place while removing it and replace it . Allow 4 hours for a beginner.

User Avatar

how long does it take to replace a carburetor on a chevy truck?

User Avatar

If this has the locking tilt wheel it is better to find a salvage yard and get the entire steering assembly . Can get for around $100. Parts and time for replacing the Ignition assembly if you can do it at all will not be worth the effort.

User Avatar

Begin by removing the retaining ring at the top of your 1986 Toyota pickup truck ignition switch. The ignition switch will slide out. Remove the wiring harness from the back of the ignition switch.

User Avatar

You need to remove the steering wheel first with a puller. There is a latch you can trip with a small screwdriver that will let the ignition switch slide out. Simply replace the switch and put the steering wheel back on.

User Avatar

1995 & 1996 checy trycks used a two piece ignition switch. I had this same problem and replace a bunch of stuff to find out the ignition switch was intermitting shutting the truck down so check before you spend money on parts you don't need

User Avatar

replace heater core in a 1991 Chevy work truck 1500

User Avatar

Chevy trucks do not have an Inerita switch. Only ford.

User Avatar

Probably a bad ignition switch.

User Avatar

insert ignition key into passenger airbag slot on the front dash and turn to off

User Avatar

the truck will not crank or anything with the key it wont even starter when you ark the starter all it does is whizz

User Avatar

Where is the fusible link in a 2005 Chevy HD truck

User Avatar

i need the ignition timing for 88 chevy 5.7 ... 350 motor i had the truck on 4 but still bad don t run good

User Avatar

How do you program a an ignition key for 2008 Chevy truck

User Avatar

ignition switch wired wrong . wire from coil hooked to hot post instead of switched post


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.