I have a 2000 Buick LaSabre and the remote trunk opener and also the button in car will no longer open the trunk. I can only open the trunk with the key. Whats the problem and how do I fix it?
Asked in Building and Carpentry
How do you reprogram your garage door opener?
Depends on the opener. Some have a set of switches in the transmitter and opener that have to match. You set whatever code you want. Some have a small square button on the opener close to where the wires for the wall button attach. Push this button, it should flash and then stay on, push the button on the transmitter, the button should flash again and go off. It should then work with that transmitter.
Asked in Home & Garden
I have a 2007 Mercedes and i am trying to set the gargage door opener remote. Manual states press the smart button on the over head opener. i cannot locate that button.?
Asked in Remote Control Devices
How do you program sears craftsman garage door opener 139.18191?
Asked in Cars & Vehicles, Toyota Avalon
How do you program a 2002 Toyota Avalon garage door opener?
Asked in Oldsmobile Aurora
How do you program the garage door opener on a 2001 Oldsmobile aurora?
Hold the 2 outer buttons down until the light in the little house icon flashes rapidly. That will clear the memory. Then you hold down the button on your opener remote while pushing the button you wish to program. When the flashing light changes from slow to rapid, you should be all set. If your opener has "rolling code" technology, you will have to program that by pushing your opener button in the car while somebody pushes the "learn" button on the opener itself.
Asked in Kia Sedona
How do you set a Kia 2005 sedona garage door opener?
Asked in Remote Control Devices, DIY Projects
How do you program a craftsman garage door opener 139.53425SRT?
The "SRT" garage door openers have an "SRT" button on the rear panel of the opener (mine is round and green). Use this button to program and also to clear previous programming. To clear previous programming, hold the "SRT" button for six seconds. To program a transmitter, hold the button on the transmitter, and while still holding it, press the "SRT" button until the opener light flashes.
Asked in Chevy Vans, Home & Garden, How To
How to program garage door opener?
It's very easy to program a garage door opener. First, press and release the learn button on the overhead garage door opener unit. The learn indicator light will glow consistently for 30 seconds. Then press and hold the button on the hand-held remote. Next, release the button when the overhead opener unit's lights blink. If light bulbs are not installed on your opener, then two clicks will be heard. That's it, the remote is ready to for you to command.
Asked in Home Construction
Where is the learn button on the garage door opener?
Asked in Cars & Vehicles, Lexus
How do I program my Lexus remote garage opener to the Craftsman garage door?
On my RX 350 and Craftsman opener I just pushed the memory button on the Craftsman opener briefly (the signal light came on next to the button) and released it. Then I pressed the sender in my car within 30 seconds. It wasn't long before the lights on the opener flashed and I then released the Lexus button. Didn't have to hold anything down very long at all.
Asked in Home Electricity
How do you change code on garage door opener?
There are two types that I know of. One has bar in both the transmitter and opener with a series of little switches on it. They can be set in any combination of on/off as long as they match. The other type only has this in the transmitter. You set the combination you want and on the opener where the wall button wires attach there should be a small 1/4 inch square button. Push it and it should flash and then stay on. Push the button on the transmitter and the button should flash and go out. The opener should receive the new code.
Asked in Lexus
How do you set Garage Door Opener On 2005 Lexus ES330?
steps to set the remote control buttons on ES330: 1) close your garage door, set the opener in lock status, 2) push the button of a existed remote control for your garage opener, at the same time push a selected button of the remote controller on your ES330, keep pushing the both buttons for over 15 seconds until there is quick flash happened in your ES330 car's remote controller, 3) push the leaning button in your garage opener once, then a leaning light will flash on the opener, 4) then immediatelly push the selected button of the remote controller on your ES330 once, then push the button again, if the door did not open at this time, you should push the button again. 5) now the you finished the setting on the remote button in your ES330.
Asked in GMC Envoy, GMC Yukon, Nissan Pathfinder
How do you program the garage door opener on an 03 Yukon?
You should be able to find this information in your owner's manual, but if you do not have one, then you can try the following: Homelink: Hold the button on the homelink system until it begins to blink. Then, while holding that button, hold the button on your garage door opener until the homelink button blinks faster. Next you will need to press and release the 'learn' button on the overhead garage door opener. Then, hold the button on the homelink you just programmed until the garage door closes. (Caution: If you press and hold the 'learn' button it will erase all of the codes programmed into the overhead unit.)
How do you program a craftsman garage door opener 139.53876?
Here are the official instructions that came with the device: Lift the cover to access the keypad. Figure 1. Decide on a 4-digit code using numbers 0 to 9. You can use a number more than once (for example, 4, 0, 4, 1). Press the selected code digits on the keypad; then press and HOLD the ENTER button, and press the SRT button on the opener end panel (behind the Control Center for screwdrive), Figure 2. (my note, this is the green button). Depending on your opener model, when you press the SRT button either the opener light(s) will flash or the garage door will begin to move. Release the ENTER button. The opener has now learned the selected code and will respond to future keypad commands. My notes: That is the official instructions. Works similar to a non-keypad transmitter. Unfortunately the green button (SRT) on the back of my opener does not seem to work. It will not clear codes or anything On the door opener attached to the ceiling by where the wall button wire attaches there should be a 1/4 inch square GREEN button. Push this and it should stay on or flash. Then push the button on the transmitter. The button on the opener should flash, this means it has recorded the transmitter. For a keypad control, On the door opener attached to the ceiling by where the wall button wire attaches there should be a 1/4 inch square GREEN button. Push this and it should stay on or flash. Once the button is on, you have 30 seconds to enter a 4 digit code in the keypad and touch Enter. The keypad on the key panel control should flash. Enter the 4 digit code again and the door should open/close.
Asked in Acura TL and TLX
How do you program the garage door opener on a Acura TL?
Asked in Hyundai Elantra
How do you program the mirror garage door opener on a 2013 Hyundai Elantra?
Asked in Household Hints
How do you get the code for a garage door that you moved into?
On the opener there should be a button by where the thin wires attach. Push the button, probably a square one and it should flash. If you have a transmitter, push it and the button should flash. If there is a key pad for the door, push the button on the opener then put in a 4 digit number on the key pad and push Enter. That will be the new code.
Asked in Building and Carpentry
How do you reprogram a garage door opener?
There are 2 types. Some have a small switch in both the remote and the opener with 9 or 10 little switches which have to be set in the same order. On or off. The other kind has a button on the opener that you push and it should either flash or stay lit and you have 30 seconds to press the remote and the opener records it's frequency and is automaticly set. 1. Remove light cover. 2. Press and hold transmitter button on remote. 3. Press and hold red receiver button. 4. Release both buttons when opener light flashes twice
How do you program your garage door opener in your 2002 Infiniti QX4?
1) Erase all your codes in the Homelink memory by pressing the two side buttons for 20+ seconds until the Homelink light flashes quickly. 2) Press and Hold your wireless garage door opener and the HomeLink button you want to program until the Homelink light flashes quickly. This will setup the Homelink opener temporarily. 3) Located and Press a scan button on the Garage door opener. Now press the button on the Homelink that you selected a few times (usually 5-8 times) until the garage door opens with the Homelink. Now its permanent. - I had this problem myself. I didn't have the wireless garage door opener so I used my keypad outside my home to program the HomeLink.
Asked in Lincoln Navigator
How do you program the garage door opener on a 1998 Lincoln Navigator?
some garage door motors have a switch or button on the motor that raises the door. This switch has to be turn to the program position. You will need to have the hand held garage door opener held about 2 inches from the opener on in the Navigator. 1. hold the button on the visor that you want to use for the for the garage until the light on visor changes. then press both the visor and hand held opener button at the same time. Pushing the the hand held about three time. I hope this works for you. It did for me.