Home
If you're wiring a 30A twistlock connector with a screwtight terminal that is not labeled and the AC cable has green-black-white wires then which wires connect where?
Wiki User
Answered 2015-07-15 18:51:18
the colors should be Green/Black/White
The Black and white do not really matter in this configuration.
Though this is the standard way of connecting the wires.
The two brass colored screws get connected to the black and red wires (phase A and B), the silver-colored screw gets connected to the white wire (Neutral), and the green screw gets connected to the bare or green wire (ground). The receptacle you have is made for 240V, you need to run a new cable assembly to it that has a black, red, white, bare. Make sure that you buy the correct wire for the 30 amp circuit (#10). Also make sure oyu have the proper breaker installed in the panel, a 30 amp, 240 (it's a double breaker that takes up 2 slots in the panel, hance the 240 volts).
I have the very same dilemma, and no, this isn't a 240V plug either. I need to use a 120V twistlock in this case to plug into a vibrative generator which seems to shed standard 120V plugs with ease.
I continue to search for this answer, perhaps somebody could leave it here.
Thanks
B
Your Answer
Still Have Questions?
Related Questions
Where is the diagnostic connector terminal location 2000 mercury villager?
Under the dash to the right of the steering column.
Where is the obd in 1994 Acura Integra rs?
It is an obd1 but there is no where. Sorry I just joint this forum and have the answer: The OBD I terminal in the 94, 95 model is the 3 terminal female connector. You need to bring your car to the garage who have the old scan tool with adapter to this terminal.
What is a battery cable puller and where can I get one?
A battery cable puller is a small hand tool specifically designed to pull a stuck battery cable connector from an automotive battery terminal without damage to either the terminal, connector, or your hands. Although there are a few different styles and brands, they generally all work the same. There will be two thin "feet" that slip beneath the cable connector, and a screw device [looks much like that used in a "C"clamp] which when turned pushes down on the top of the battery terminal, thus pulling the terminal clamp upward off of the tapered terminal. Battery cable/terminal clamp pullers can be bought at most auto parts supply stores. Very occasionally, some auto supply stores [those that loan tools] will loan it to you.
Is the positive connector on a Lead-acid battery white?
The positive connector on a lead acid battery is frequently not white. In the United States, the wire that leads to it is usually red. The black wire leads to the negative terminal. The positive terminal on the battery is always indicated by a plus, +, sign. The Negative terminal is indicated by a minus, -, sign. The negative terminal is usually attached to the body of the car. (Cars have a negative ground, except for 1935-1948 Fords.) The positive connector is usually attached to the solenoid and generator. So check the wire that comes from the battery to the solenoid. That is positive. Check to make sure it is connected +.
Where is the C-3 diagnostic lead on a 307 olds on a 88 Cadillac brougham?
It is available at the ALDL connector, terminal 'B', located under the instrument panel, just right of centre. Terminal 'A' is ground, so it is possible to use a short jumper to ground this terminal.
Where is the location of the diagnosis connector obd 1 connector on a 1995 to 1998 Honda odyssey?
its under the left hand side of the dash this is the bridgable type non obd connector (2 pin) so no code reader needed do not bridge the 3 terminal connector,, to clear code remove fuse f39 (7.5amp) from underbonnet for aprox 10 sec
1995 tracker where is the connector to jump for the check engine light to make it blink the codes?
I had the same problem and found that mine was using a six prong plug located in the engine compartment near the battery. It is called a Duty Check Data Link Connector (DC-DLC) and the wires are: 1 2 3 4 5 6 1 - Has no wire 2 - Diagnostice Request Terminal, Blue with Yellow stripe 3 - Diagnostic Output Terminal, Purple with Yellow stripe 4 - Ground Terminal, Black 5 - Test Switch terminal, Blue with Red stripe 6 - Duty check terminal, Purple I jumped terminal 2 with terminal 4 and got my codes, I have some pics at: http://home.stx.rr.com/hesszoo/tracker/ The plug listed as 4 is the one your looking for.
Parts of a monochrome television and its function?
*lamp enclosure *mounting bracket *reflector *side terminal *glass *ballast connector *ballast wires *Ignition chamber
Where is the OBD II terminal located in a 99 Accord?
The 1999 Honda Accord OBD 2 port is above hood release; connector faces down
Did the 1995 Chevy silverado have the OBD-II port inside the cab?
The data link connector did change from OBD-1 to OBD-2 sometime during the middle to late 1990's. Both styles of connectors are black and located under the drivers side dash. The OBD-1 connector is more of a rectangle shape and should have 12 terminal slots in it, each terminal slot in directly on top of each other. The OBD-2 connector is different in shape, kinda like a rectangle with 4 rounded corners. The bottom of the connector is shorter than the top. Also the top row of terminal slots has more terminals in it than the bottom. Hope this helps! The switch between OBD-I and OBD-II came in 1996
How do you replace the alternator on a 1989 Toyota Corolla?
Remove the Negative terminal. loosen all belts as well as the tensioner bracket first then unplug the connector (+), then remove the remaining 4 bolts. Try disconnecting the negative terminal while the engine is on, if the car dies it is your alternator.
Where is the turn signal flasher on a 1997 Isuzu Hombre?
Turn flasher is near the cigarette lighter but its on the second/ right round aluminum can, cause the left can is a hazard relay switch just clean the connector with sand paper, due to time of use dirt or just oxidation is on the terminal. And it has 2 terminal only, if you buy new one it has 3 terminal.
How do you change the starter in a 1997 ford f-150?
Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. Start the engine several times to check starter motor operation.
How do you change the starter on a 97 Ford Expedition?
Starter = Removal & Installation = 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.
Starter removal for a 2001 half ton f150?
StarterRemoval & Installation 1. Disconnect the negative battery cable.2. Raise and safely support the vehicle.3. Remove the starter terminal cover.4. Remove the terminal nut and separate the battery starter cable from the starter motor.5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.6. Remove the starter motor retaining bolts.7. Remove the starter motor from the vehicle.To Install:8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.11. Install the starter solenoid safety cap. If equipped.12. Lower the vehicle.13. Connect the negative battery cable.14. Start the engine several times to check starter motor operation.
How do you change the starter on a 1992 f150 6-cylinder?
StarterRemoval & Installation1. Disconnect the negative battery cable.2. Raise and safely support the vehicle.3. Remove the starter terminal cover.4. Remove the terminal nut and separate the battery starter cable from the starter motor.5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.6. Remove the starter motor retaining bolts.7. Remove the starter motor from the vehicle.To Install:8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.11. Install the starter solenoid safety cap. If equipped.12. Lower the vehicle.13. Connect the negative battery cable.14. Start the engine several times to check starter motor operation.
How do you wire up a starter for a 1995 ford truck?
StarterRemoval & Installation 1. Disconnect the negative battery cable.2. Raise and safely support the vehicle.3. Remove the starter terminal cover.4. Remove the terminal nut and separate the battery starter cable from the starter motor.5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.6. Remove the starter motor retaining bolts.7. Remove the starter motor from the vehicle.To Install:8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.11. Install the starter solenoid safety cap. If equipped.12. Lower the vehicle.13. Connect the negative battery cable.14. Start the engine several times to check starter motor operation.
How do you reconnect the wires to the starter of a 1994 ford f 150XL?
StarterRemoval & Installation 1. Disconnect the negative battery cable.2. Raise and safely support the vehicle.3. Remove the starter terminal cover.4. Remove the terminal nut and separate the battery starter cable from the starter motor.5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal.6. Remove the starter motor retaining bolts.7. Remove the starter motor from the vehicle.To Install:8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm).9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm).10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid.11. Install the starter solenoid safety cap. If equipped.12. Lower the vehicle.13. Connect the negative battery cable.14. Start the engine several times to check starter motor operation.
Starter installation for 97 expedition?
Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.
What extensions to use to remove the starter of a 2000 expedition?
Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.
Where is the starter on a 2000 Lincoln Navigator?
Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. Start the engine several times to check starter motor operation.
How do you replace the starter on a 2001 Ford Expedition?
Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. Start the engine several times to check starter motor operation.
How do you take off a starter for 1998 ford expedition XLT?
Starter Removal & Installation 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.
How do you install the starter on 2004 f150 stx 2wd?
Starter = Removal & Installation = 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.
How do you Replace starter F-150 1997?
Starter = Removal & Installation = 1. Disconnect the negative battery cable. 2. Raise and safely support the vehicle. 3. Remove the starter terminal cover. 4. Remove the terminal nut and separate the battery starter cable from the starter motor. 5. Disconnect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. Ø To disconnect the hard-shell connector from the solenoid (S) terminal, grasp the plastic shell and pull off; do not pull on the wire. Pull straight off to prevent damage to the connector and (S) terminal. 6. Remove the starter motor retaining bolts. 7. Remove the starter motor from the vehicle. To Install: 8. Place the starter motor in position and install the starter motor retaining bolts. Tighten the bolts to 15-20 ft. lbs. (20-27 Nm). 9. Install the battery starter cable and a terminal nut to the starter motor. Tighten the terminal nuts to 79 inch lbs. (9 Nm). 10. Connect the solenoid (S) terminal connector, if equipped with a starter mounted solenoid. 11. Install the starter solenoid safety cap. If equipped. 12. Lower the vehicle. 13. Connect the negative battery cable. 14. Start the engine several times to check starter motor operation.
Mercury VillagerAcura IntegraCar BatteriesChemistryCadillac BroughamHonda OdysseyCheck Engine LightTelevision and VideoHonda AccordChevy SilveradoAlternatorsIsuzu TrucksFord Trucks and SUVsFord ExpeditionFord ExplorerFord F-150Car Starting ProblemsChevy Blazer S-10Ford Expedition XLTLincoln Navigator
Still have questions?
