answersLogoWhite

0


Best Answer

take it to midas muffler

User Avatar

Wiki User

โˆ™ 2006-03-10 05:41:30
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: If you can put true daul exhaust on a 5.7L Chevy k1500 can you do the same on a 5.0L Chevy k1500 with out messing up needed back pressure you need good tips for dauling out your 1996 5.0L k1500?
Write your answer...
Submit
Sign up for more answers

Registered users can ask questions, leave comments, and earn points for submitting new answers.

Already have an account? Log in

Related questions

Why an intake pressure boost in a two-stroke engine is a must?

After the exhaust blowdown is nearly complete, the intake slot starts to uncover. At this point an intake pressure boost is needed to increase the pressure at which the air enters the cylinder, to push the remaining exhaust gases and fill the cylinder with combusted air-fuel mixture.


The pressure needed to stop osmosis is called?

osmotic pressure


2002 Ford Taurus oil light flickers?

my oil light is flickering on 02 ford tourus it has oil what could it be? The shop told me they needed to replace the exhaust gas pressure sensor,the problem was fixed!


When your done screwing out the nails on the dsi what do you do with the battery to get on the internet?

The DSi is internet enabled already, no messing around with the battery is needed.


Why is pressure needed in the circulatory system?

Pressure is needed so that the blood will get to all parts of the body and all cells of the body.


What diameter exhaust pipe is needed for a 1500cc engine?

the best would be 1.75 inch


What type of air pressure are needed for a hurricane?

Hurricanes have intense low pressure


Why is a pump needed in a hydraulic system?

An hydraulic system is a high pressure system hence the pump provides this pressure needed to transfer the force.


How much bar needed to convert air to liquid under pressure?

Initially, a minimum of 5.2 bar is needed to convert air to liquid under pressure. This pressure is for the initial process. For the final process, less than 1.7 bar is needed.


Why inlet valve is bigger than exhaust valve?

because the inlet valve has to hold back pressure from the gas pump where as the exhaust valve has nothing to hold back but the compression of the ignited fuel and such a force is applied at the face of the valve. the face of the valve is in the cylinder so the force is a push not a pull meaning a bigger exhaust valve is not needed because the valve dose not have to fight back to keep it's self closed.


The pressure needed to stop osmosis is?

Hypertension


What water pressure is needed to operate a 21 psi pump?

You have things confused. -Water pressure cannot operate a pump. - More detail needed.


What types of air pressure are needed for a hurricane to form?

Hurricanes have low air pressure


What is the pressure needed on valve on 1996 ford escort?

Tire pressure 32 lbs. Fuel pump pressure 46lbs.


What pressure is needed to compresses propane to liquid?

7897t586u67


How much pressure is needed to crush a human?

45ton


The pressure needed to stop osmosis is called the?

hypertension


What is osmotic pressure?

The amount of pressure needed to stop osmosis: a solution's potential pressure caused by nondiffusible solut particles in the solution.


Why high pressure needed in autoclave?

To sterilise effectively the water in the autoclave needs to reach a temperature of 120°C. Since water at atmospheric pressure boils at 100°C, a higher pressure is needed to reach that temperature.


How much Pressure is needed to crush a soda can?

Full can? Average should be about 200-250 lbs pressure.


How much pressure is needed to break your leg?

Just 20 pounds of pressure if you're applying it from the side!


What is minimum systolic blood pressure needed when applying mask with continuous positive airway pressure?

90


When would less helium be needed to fill a balloon?

The lower the atmospheric pressure, the less helium is needed.


Where is the exhaust manifold located on a 1997 Dodge Avenger?

More information is needed to answer this question properly, such as; is the engine a 4 or 6 cylinder. In the case of a 6 cylinder, their are 2 exhaust manifolds; the front exhaust manifold is located under the hood between the radiator and the engine: when you check your oil level by grasping the dipstick your hand will be just a few inches above the exhaust manifold. Basically, follow the exhaust pipe(s) to the engine and where it connects to a device that splits the exhaust 3 or 4 ways, that device is your exhaust manifold.


What is needed for contact metamorphism to occur?

Heat and high pressure