answersLogoWhite

0


Best Answer

In a word; no. If you ever plan to have both groups of equipment running at the same time the panel will be constantly tripping. Also most "equipment" normally runs on 220v which requires two hots: both phases.

User Avatar

Wiki User

โˆ™ 2015-07-15 19:26:35
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: If you have a 100A 2 phase panel and 2 groups of equipment 70A each can you connect one group to first phase and the other to second?
Write your answer...
Submit
Related questions

Is the accent in connect on the first or second syllable?

The emphasis in the word "connect" is on the second syllable.


The second crusade differed from the first because in the second?

crusaders took too much equipment


How do you connect two deep cycle 12 volt batteries in parallel to an RV?

First off you must have the same type batteries. Connect the positive post of the first battery to the positive post of the second battery. Then connect the negative post of the first battery to the negative post of the second battery. Now connect the positive post of the first battery to the positive connection on the vehicle. Then connect the negative post of the first battery to the negative cable of the vehicle. Click the link for a diagram.


How do you connect resistance is series?

I'm going to take this as "How do you connect resistors is series?" just connect one wire of the first resistor to one wire of the second.


How did the Second Crusade differ from the first?

crusaders took too much equipment.


Can i Use 2 wireless routers on one modem?

Yes, you can. But you have connect them in series not in parallel. It means that you connect first router directly to the modem, and the second connects to the first one.


Can master slave flip flop can be formed by SR flip flop?

Yes. You need two gated input SR flipflops, and an inverter. Connect the Q output of the first flipflop to the S of the second. Connect the notQ output of the first flipflop to the R of the second. Connect the clock to the gate input of the second flipflop, and to the input of the inverter. Connect the output of the inverter to the gate of the first flipflop.


What are the two groups of violins?

First violin (which is harder) and Second violin (which is easier)


Name the first and second largest groups pf people in Iraq?

terrorist


What functional groups are found in all monsaccahrides?

Hydroxyl groups are found in all monosaccharides along with a carbonxyl on the first or second carbon.


During the Han dynasty who belonged to the first and second social groups?

The first group was the emperor, his court and the scholar's that had government jobs The second was the peasants


How do you connect diodes in series?

You connect the anode of the second diode to the cathode of the first diode. The anode of the first diode and the cathode of the second diode become the two terminals of the combined diodes. The combination acts as a voltage source. You can also connect the anode of the second diode to the anode of the diode. The combination serves to block any signal going through, until the breakdown voltage of one of the diodes is reached.


Is concert a first or second accent syllable?

Yes. A musical concert has a first-syllable accent. To concert the efforts of a groups has the accent on the second syllable.


My I phone says it cannot connect to YouTube why?

There are a couple reasons for this. The first reason is that you do not have a data plan for your iPhone, so you cannot connect to the internet. The second reason is that you are not connected to Wi-Fi, which is also what you might need to connect to YouTube.


What terminal do you connect first positive or negative?

Connect positive first and negative last.Connect positive first and negative last.


Can a diagram for two 12V deep cycle motor home batteries connected to output 12V be supplied?

You just connect them in Parallel. Two 12 volt batteries connected in parallel will output 12 volts. Two connected in Series will output 24 volts. Just connect the negative terminal on the first battery to the negative on the second battery. Then connect the positive terminal on first battery to the positive on the second battery. Connect the cables to the second battery, positive to positive and negative to negative. Click the link for a diagram.


Is device an accent on first syllable?

No, in the word "device" (object, apparatus, piece of equipment), the accent is on the second syllable.


How many groups of settlers were sent to Roanoke?

For the first group, approximately 75 men. For the second, about 117.


Can you connect a cable modem to a 2Wire DSL wireless modemrouter?

Yes you can, you have to do that like following. Connect one DSL wireless modemrouter to the cable modem, and another wireless modem connect in the first wireless modemrouter. You have to understand that internet speed on the first DSL router will be rather higher then for the second one.


Can you connect a wireless router to desktop PC?

Yes, you can. There are at least two ways. First one is to get a wireless adapter for your desktop. Second one is to use a LAN cable to connect your desktop to your router.


How does you connect Samsung gts5620 with your PC for net?

First, your question should be like this..."How do you connect Samsung..."Second, no answer :)


What is can sealer?

can sealer-is an equipment used to seal tin cans with its first and second operation rollscan sealer function


What are the two pedals used on the piano for?

The first pedal is to dampen the sound and the second pedal is to connect all the notes played together.


How do you complete level 47 on 100 Floors?

Change the patterns so they connect the DOT (around the middle) to the lightning bolt in the bottom right corner. The lines won't exactly match up, but if you imagine they do, and you make a continuous path from the lightning bolt to the center dot, the door will open. Tap each tile to turn it. All the corner tiles need to be turned so that both ends lead to another block and not into a wall, floor, or ceiling (the lightning tile can't be turned, but it already doesn't point to a wall). (No tiles should lead to a wall, floor, or ceiling.) In order of the path from the dot to the lightning: Third row, third column: The dot connects to the tile below it. It can't be moved. Fourth row, Third column: This tile should connect to the dot and to the tile to the left of it. Fourth row, second column: This tile should connect left and right. Fourth row, first column: The corner tile should connect right and up. Third row, first column: This tile should connect down and right. Third row, second column: This tile should connect left and up. Second row, second column: This tile should connect down and left Second row, first column: This tile should connect right and up First row, first column: The corner should connect down and right First row, second column: This line should connect left and right. First row, third column (top middle): This tile should connect left and down. Second row, third column: This tile should connect up and right Second row, fourth column: This tile should connect left and up First row, fourth column: This tile should connect down and right First row, fifth column: The corner should connect left and down. Second row, fifth column: This line should connect up and down Third row, fifth column: This tile should connect up and left. Third row, fourth column: This tile should connect right and down Fourth row, fourth column: This tile should connect up and right (to the lightning bolt) Fourth row, fifth column: The lightning bolt connects to the left, and cannot be changed. See the screenshots in the related link.


How do you connect multiple lights to one switch starting at the light?

You put switch in series with the black supply wire and the black wire to the first light. Then connect black wire of first light to black wire of second light, black wire of second light to third light and so forth. Do the same with the white wires and ground wires.