0
If you have a 4 cast iron stack with a 4 outlet to the toilet and the pipe coming up to the toilet is lead how do you attach a toilet flange to this 4 lead pipe?
Wiki User
∙ 12y ago
The flange is actually a ring that the lead comes up through the middle of. The ring is secured to the floor and the lead is beat down against the flange. T would actually consider doing away with this lead bend as they are currently 50 years old or older. That is to say they stopped using them about 50 years ago and they are currently failing in a lot of homes. I w3ould cut the lead out leaving the brass stub in the cast iron where the lead attached, and repipe with PVC to that brass stub and attatch it with a fernco coupling. Three inch PVC will slide right inside that brass stub to make a real nice connection,
Answerif you have the pipe flush with the finish floor you can get a plastic flange with a rubber ty seal gasket around it. this will fit inside the 4" pipe. or if the lead is exposed you can snap it at the cast iron and transition to plastic.Wiki User
∙ 12y ago
Add your answer:
Earn +20 pts
Why is the toilet not sataying in place?
Broken toilet flange. Toilet flange bolts may be loose.
What is the roughing in measurements coming up through the floor for a toilet?
Depends on the toilet being purchased, but generally 12 inches from the wall to the center of the toilet flange for a residential toilet.
To what is a toilet mounted?
Toilet flange.
Do you glue the toilet flange into the toilet drain?
Usually toilet flange is glued down onto plastic drain pipe. There is a toilet flange that can be glued inside of plastic drain pipe also.
Toilet Flange Repair?
When a toilet rocks like a rocking chair, leaks water around the floor connection or displays other signs of insecure foundation, the toilet flange needs replaced or reset. A toilet flange is the metal plate located below the toilet which connects the toilet with the sewer outlet pipe while securing the toilet with the floor. When a toilet is initially constructed it is secured to the floor with screws and the junction is sealed with a liberal application of beeswax. When a toilet is securely fastened and maintained properly, proper function including no water leakage or odor present is the norm and not the exception. An indication of possible need of attention is the presence of black mold on the floor near the base of the toilet. Also evidence of water leakage or an unpleasant odor originating from the toilet base is a reliable indicator of the need for a toilet flange repair. Regardless of who does the repair of a toilet flange, the following criterion is paramount for a job well done. It is also important to follow certain procedures, from diagnosis to completion of the job. Tools and materials: screws, screw driver, flange bolts, wax rings, caulk and a flange repair kit. Remove the Toilet: After shutting the water supply to the toilet, flush the toilet water from the tank and bowl before releasing the toilet from its floor connection. Unscrew the bolts and nuts on the sides of the toilet base. Secure the bowl and tank and lift the toilet from the floor connection. Repair the Toilet Flange: Old wax must be cleaned off from the old flange. Flange bolts may need replaced due to corrosion from water leakage. Position the flange bolts in the holes of the repair kit and place it on the floor as the previous flange setup. This step ensures proper placement of the flange and prevent leakage. Fix the Flange and Toilet: Follow manual instructions of the original toilet manufacturer when screwing the flange to the floor. Place wax rings and remount the toilet with bolts and nuts.
Should you glue your toilet closet flange to your pipe?
No, it is not recommended to glue the toilet closet flange to the pipe. The flange should be secured to the floor using bolts or screws, and the toilet is then secured to the flange using wax rings or sealing gaskets. Gluing the flange to the pipe can make it difficult to remove or replace the toilet in the future.
How far should a toilet flange be from a tub?
15 inches from outside edge of tub to center of toilet flange.
What if a toilet flange will not fit in the drain pipe?
The easiest solution would be to move the toilet so that it lines up with the waste pipe.
What is a compression flange?
A compression flange is used to connect a toilet to the sewer line.
How to Install a New Toilet Flange?
Installing a new toilet flange is a fairly simple process that should take no more than 15 to 20 minutes. A properly installed toilet flange will ensure years of dependable use. If the old flange needs to be removed, this will increase the installation time. These instructions assume you are starting with a waste pipe that does not have a toilet flanged installed. If the old toilet flange is still installed on the waste pipe, begin by removing it, then following these procedures.The following items are needed to complete this procedure:New toilet flangeAdjustable wrenchScrewdriver (Phillips or straight head)Hacksaw (if modification to waste pipe is needed)Purple primer and solvent cement (if PVC flange is installed)New wax seal or waxless toilet sealPlace the new flange on the waste pipe and ensure the pipe height is proper for the flange to be affixed to the subfloor. If modifications need to be made to the waste pipe, use a hacksaw to cut the pipe to the proper height.Ensure the new flange is sitting level to the floor. The flange must sit level and flush to the floor for the toilet to properly seal to the new flange.Install the new flange on the waste pipe with the bolts positioned so they will fit into the toilet mounts. If a PVC flange is used, apply purple primer to the outside of the waste pipe and solvent cement to the inside of the flange, then press the flange firmly on the waste pipe. Be aware, once these item are attach using primer and solvent, they cannot be removed or adjusted. Be sure the flange is positioned and inserted properly on the waste pipe.Secure the new flange to the subfloor by screwing the flange directly into the floor.Apply the new wax seal to the flange or affix a new waxless toilet seal directly to the underside of the toilet.A waxless seal is commonly overlooked by consumers. Ask your retailer about a waxless seal. Waxless seals are cleaner to install and uninstall and can be reused even if the toilet is removed later.Mount the toilet back onto the new flange and secure it using a washer and nut on the flange bolts. Tighten each bolt with an adjustable wrench. Be very careful not to over tighten the bolts. If the bolts are over tightened, the porcelain toilet will crack.Your new toilet flange is installed and ready to use.
Will a toilet flange at three eighth of an inch above a finished floor seat wax seal to toilet properly using a Kohler toilet?
Yes As long as the flange does not hold the toilet off the floor it will be fine.
What is the distance a toilet flange has to be placed from the back and side walls?
The toilet flange is installed 12" from the FINISHED wall surface to the center of the flange, and 16" (residential), or 18" from the finished wall to center of the flange in commercial,or wheelchair accessible applications.
