Car Fuses and Wiring
Ford Escort
VW Cabriolet
Turn Signals and Hazard Lights

If your turn signals and hazard lights will not turn on even after changing bulbs and fuses where can you get a wiring diagram or otherwise find the route of the problem for a 98 Ford Escort Wagon?

12

Top Answer
User Avatar
Wiki User
2010-11-17 23:31:01
2010-11-17 23:31:01

odds are its the flasher, its a small silver can somewhere under the dash, its the thing making the clicking sound when they did work

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

Fix the rear signals. The most common cause of this is the wires going from the front to the rear. These might need to be replaced. It could of course be as simple as changing the bulbs. It might have something to do with a fuse, but if so, then the wires are probably faulty. A shortcut somewhere. Replacing wires would fix this. It might be due to a faulty relay. Changing this might fix the problem.

User Avatar

It could have a bad bulb in it. Try changing that. That should take care of your problem. I had the same problem a few days ago, paid $11 for a turn signal flasher, fixed it.

User Avatar

The PA Motor Vehicle Code, ยง 3334. Turning movements and required signals- says that you will use your turn signals or hand signals when you are turning or changing lanes.

User Avatar

what fuse number is for turn signals

User Avatar

a transmitter that sends out morse code signals

User Avatar

Haynes makes a repair manual for the 1998 Chevy Z-71 contains a wiring diagram for the turn signals. This book is available at most major book stores.

User Avatar

We use clock signal in timing diagram because the microprocessor operates with reference to clock signals provided to it. At pins X1 and X2 we provide clock signals and this frequency is divided by two. This frequency is called as the operating frequency.

User Avatar

If the turn signals and emergency signals don't workout sounds like an electrical problem's would suggest that you take it into the closest shop to get the problem diagnosed properly.

User Avatar

Activate the 4-way flashers. This might work, temporarily. This problem has had a factory recall. Go to a GM dealer and see if they'll fix it for nothing. Apparently it involves changing the hazzard switch in the dash.

User Avatar

Good news! That's not a problem. They're supposed to becurved.

User Avatar

Electrical signals are either direct current (DC) or alternating current (AC). For DC signals, information is carried by the existence of a DC level, or it's absence. This is binary signalling, and communicates either a '1' or a '0'. An AC signal conveys information by either changing one of the three properties that AC signals have: 1) changing the amplitude of the signal (this is amplitude modulation, like an AM radio) 2) changing the frequency (this is frequency modulation, like an FM radio station) 3) changing the phase of the AC signal. This is used in the faster of the old-style computer modems, as well as DSL modems

User Avatar

When you are making a turn, when you are changing lanes, or when you are pulling away from the curb or are parallel parking. Activate turn signals 200' before making a turn.

User Avatar

It deals with the amount of transmission that flows between two currents:

User Avatar

check the recalls there is something in there about tail light and signals

User Avatar

by changing the amplitude or frequency of the radio waves.

User Avatar

because that what they are for. otherwise they would be orange headlights.

User Avatar

As of 2010 the answer is no. It is recommended to use your turn signals when changing lanes, but not a law.

User Avatar

changing the neuron membrane structure, which changes the shape of receptor proteins

User Avatar

Changing day length and drop in temperature.

User Avatar

Your problem is most likely the turn signal relay im having a problem similar to yours but when my signals wont work neither do my hazards

User Avatar

Well I personally have a 2000 Malibu LS and have had the same troubles random clicking noises when signals aren't on then no signals or random signals. The problem is your hazard relay switch, it is located in your dash board very easy abd cheap fix.

User Avatar

This is a process which reduces the data rate or file size of digital audio signals. For processes which reduce the dynamic range (without changing the amount of digital data) of audio signals,

User Avatar

A powered audio mixer is used for combining, mixing, routing and changing the level, timbre or dynamics of audio signals. They can mix analog or digital signals depending on the mixer.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.