answersLogoWhite
Cars & Vehicles
Alternators
Ford Expedition Eddie Bauer
Ford Expedition XLT

In a 1992 Chevy Beretta alternator how many wires should be connected?


Top Answer
User Avatar
Wiki User
Answered 2011-09-12 22:53:54

There should be one female plug-in and one separate hot wire that is hot anytime the battery is hooked up.

001
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Your Answer

Still Have Questions?

Related Questions

What size alternator for a 1994 Chevy beretta?

A 1994 Chevrolet Beretta with the 2.2 or the 3.1 engine takes a 105 amp alternator.


What size alternator does a Chevy beretta use?

105 amp.


Where is a 94 Chevy beretta z26 voltage regulator?

The regulator on a 1994 Chevy is inside the alternator.


Where is the alternator on a 1990 Chevy pickup?

The alternator should be on the front of the motor with a belt on the pulley and wires connected to the back of it that can be removed.


How do you replace the alternator in a 95 Chevy beretta?

Go to autozone.com. They have this information on their website.


Where is voltage regulator located on 1996 Chevy beretta?

The voltage regulator is built into the alternator.


How do you replace a 1990 Chevy Beretta battery?

how to replace a 1990 Chevy Beretta battery


Where is the freeze plug on a 91' Chevy beretta gt?

i have a 1994 Chevy beretta and they are under the engine


What is the difference between European spec Chevy Beretta and US spec Chevy Beretta?

A very detailed write-up should answer your question here:http://www.bstuff.com/lofiversion/index.php?t30468.html


Known Chevy Beretta cam shaft problems?

Does anyone know of any chevy beretta cam shaft problems?


Third brake light on a 96 Chevy beretta?

how to change third or center brake light on Chevy beretta 95


How do you replace the complete wiring harness in a 1994 Chevy beretta?

Bstuff.com should have the info you are looking for.


How long does it take to replace an alternator on Chevy Trailblazer?

It should only take about an hour at the most to change the alternator.


Where do you get a right rear strut assembly tower for 1990 Chevy Beretta GT?

There are no rear struts in the Chevy Beretta. Only shocks.


I have a 1995 Chevy Beretta with a bad 3.1L and a 1993 Chevy Lumina with a good 3.1L motor is this a possible swap?

the beretta and lumina motors are about the same i have a lumina motor in my 95 beretta


How do you change the alternator on a Chevy Beretta with a V6?

Very easy. Disconnect the battery. Lift up the belt tensioner and slip the serpentine belt up off the alternator pulley. Remove the 3 bolts holding down the alternator. Unplug the voltage regulator cable from the alternator. Disconnect the positive battery cable from the alternator. Installation is the reverse of removal.


Where do you find a replacement dashboard top for a 1990 Chevy Beretta GT?

Ebay. Just enter Chevy Beretta under parts and accessories


Where is the map sensor on a 1991 Chevy lumina euro?

Should be by the alternator in the back


How much does a Chevy beretta weigh?

2150lbs


Are the transmissions in a 1989 Chevy Beretta and a 1992 Chevy Beretta interchangable?

depends on engine, mounting, body, ecm, and about a million other things, but possibily


Can someone give me a diagram of a fuse box for a 1993 Chevy Beretta?

can someone give me a diagram of a fuse box location for a 1993 Chevy beretta


How do you get the alternator light to go off on a 1997 Chevy Malibu?

If the alternator is working properly then it should go off onec the engine has started. If it does not then you probably have afaulty alternator.


How do you change th alternator on a2006 Chevy hhr?

how do you change the alternator on a chevy 2006 hhr


Will a 2.8 engine from a 1988 Chevy beretta fit a 1989 Chevy blazer?

Yes it will, but you have to put all the blazer engine stuff onto the beretta engine...


Where is the beretta computer or module located?

I am trying to find the 1988 chevy beretta computer module and where is it located?


Still have questions?