0
In my 1986 Chevy silberado my back brakes have no flluid going to them I think it is the splitter valve or the proportioning valve what do you think?
Wiki User
∙ 16y ago
I think you are right but it could also be the master cylinder or a clogged or broken brake line.
Wiki User
∙ 16y ago
Add your answer:
Earn +20 pts
How many flluid ounces in 3 liters?
Three liters is about 101.4 fluid ounces.
Renault scenic 16v automatic 1999 let me know where is the auomatic transmission flluid dipstick located to check the transmission fluid?
under the hood!!! try looking on the left front side of the engine down low
Is tonic water a diurretic?
Tonic water is not a diurretic. Tonic water can be drunk alone during the day as regular water is, or is can be combined with another beverage to prepare a favorite drink. A diurretic is a prescription prescribed by a physician and administered by a pharmicist, the purpose of which is to expel excessivel flluid from the bladder. Sometimes this preparation is known as a "water pill" since it prompts higher than usual urination.
How do you remove rear axles on Kubota rtv 900?
Jack the unit up and place jack stands under the frame. Drain your flluid. Remove rear wheels and hubs. The rear axles are actually 2 shafts slipped together. There is a plastic boot with a band at the top and bottom that must be removed. Use wire cutters to cut the bands. Once this is done to both sides, remove nuts holding the rear bumper/axle assembly in place. With the nuts removed the rear bumper/axle assembly can be rotated downward and side to side to release the shafts from each other, If you can not get them to release you may have to use a screwdriver to break the plastic boots free from the shafts. Once the rear bumper/axle housing is removed the outer shafts are pressed into the housing. The inner shafts are bolted to the transmission. All you need to do is remove these bolts and the inner half shaft will come out.
How do you bleed a clutch master cylinder?
You can do it a few ways. One is called BENCH BLEEDING in which you would put the master cylinder in a vise and run a bleeding kit into the reservoir and pump the piston with a screw driver until there are no more bubbles ( you will still have to follow the next step as well but this makes it go faster) THIS IS ONLY IF YOU ARE INSTALLING A NEW MASTER CYLINDER. The second way is the normally process in which you have someone sit in the car and pump the pedal 4-5 times ( pushing the pedal all the way down and up each time ) and on the last pump have your buddy hold the pedal to the floor then you open the valve on the slave cylinder and let the fluid out ( dont let them release the pedal until you close the valve or you will suck air back in) do this this a few times until the pedal feels good. If you are alone and dont have someone to help you, you can just open the valve on the slave cylinder and let it GRAVITY BLEED. As we all know fluid is heavier than air so after awhile the fluid will push out the air in the system. Keep checking the reservoir as you dont want to run it dry. This is also the same as when working on the brake system.ANSWERINSTALL THEM YOU DONT WANT TO PUSH THE PUMP FORWARD BACK FORWARD BACK WITH FLLUID ON THEY HAVE TO BE VIRGIN WITH NOTHING AND THEN BLEED GRAVITY OR VACUUM BLEED IT THE RESON FOR THAT IS BOTH WAYS YOUR NOT BEATING UP THE PUMPS,THEY WILL WORK AMAZING IF PREVENT FROM BEATING YOUR PUMPS.GRAVITY IS OK ,VACUUM BLEED IS A DEALER JOB WELL DONE,YOUR MAIN KEY IS YOU HAVE NO LEAKS BY MAKING SURE THEM FLUID PIPES ARE INSTALLED PROPERLY YOU HAVE TO TIGHTEN THEM OR CLIP VERY PROPERLY IT IS VERY IMPORTANT YOU GET THEM RIGHT WITH NO LEAKS,THATS IT YOU JUST SAVE YOURSELF SOME BIG LABOR MONEY BUY YOURSELF AN IPOD OR SOMETHING,AND 1 MORE THING JUST TRY TO DO 1 GOOD BLEED,HOPE THIS HELPS
