answersLogoWhite

0


Best Answer

Both dots are at 12 O'clock with the #1 piston is at TDC. With #1 piston at TDC, The crank gear ( dot ) will be at 12o'clock

And the cam gear ( dot ) will be at 6 o'clock

That makes both Dots stright over top of each other

User Avatar

Wiki User

โˆ™ 2008-12-13 03:49:07
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar

Add your answer:

Earn +20 pts
Q: In what direction should the cam and crank gears be pointing when installing a new chain and gears on a Chevy 350?
Write your answer...
Submit
Related questions

What position should the plug on the distributor be in at TDC on a 4.3 Chevy?

The rotor inside the distributor should be pointing at the #1 spark plug.


What is procedure for installing a new distributor shaft in a 1974 Chevy 350 motor with electronic ignition?

remove dist.cap.unplug wires and hoses mark rotor where it is pointing...remove holddown bolt remove dist.


Installing a cb radio in Chevy Impala?

Installing a CB radio in a Chevy Impala begins which installing the mount and location a suitable power source. The radio is then mounted to the dash, wired up, and the antenna connected.


What direction should the thermostat be in on a 1994 Chevy Suburban 5.7?

The spring on it goes down in the engine.


2000 Chevy venture how to remove radiator drain plug?

The radiator drain plug on a 2000 Chevy Venture is removed by slowly turning it in a counter-clockwise direction. Care must be taken when re-installing the plug to prevent cross threading.


Installing a tach on a 1970 Chevy 400cc engine?

I wasnt aware Chevy used a 400cc engine


When the timing mark on the dampener is at zero Where should the distributor point to on a 72 Chevy 350?

It should be pointing to the #1 cylinder, That is the first spark plug on the driver's side up front.


Where is number 1 on a 85 Chevy V8 dist cap?

should be in a straight line from center of the distributer cap to the #1 cylinder, or pointing at the #1 cylinder


Installing crankshaft position sprocket on 350 Chevy?

What do you need to know about it.


How do you torque when installing flywheel in a 1979 Chevy truck?

with a torque wrench


What is the proper procedure for installing struts on a 1998 Chevy Astro van?

A 1998 Chevy astro has shocks instead of sturts.


How much does installing a leveling kit to a Chevy Silverado cost?

about 150$. roughly


What is the firing order for a 1990 Chevy Silverado for the distributor cap?

if its a v-8 it is 18436572 number one on the cap should be pointing at number 1 cylinder is there a picture of the cap


What is the rotor direction on a 350 Chevy?

clockwise


Diagram for installing serpitine belt?

1999 Chevy cavaler diagram of sepitine belt


How do you change a cabin filter on a 2007 Chevy Silverado?

It does not have one after 2005 they stopped installing them


What does a red arrow pointing down mean on a 1999 Chevy cavalier?

Add engine coolant


Where should rotor point big block Chevy 71 some say the?

When the #1 piston is at TDC./ TOP DEAD CENTER on the compression stroke the rotor should be pointing towards the #1 cylinder when the distributor is installed correctly.


Which direction is distributor rotation Chevy 454?

Clockwise.


Which direction to prime Chevy oil pump?

clockwise


What direction does a Chevy small block turn?

clockwise


What direction is the crankshaft rotation on a Chevy 454?

Clockwise


Does fuel on carb need to be turned up after installing a bigger cam in a 350 Chevy?

Not usually.


What are the torque specifications when installing spark plugs on a 2002 Chevy Malibu?

11 ft/lbs


Where schould the rotor point on a Chevy 350 at td i did not take it apart?

Should be pointing at the wire that goes to the cylinder that is at tdc. You can contact me for more info as I am having a hard time trying to know what you are asking.