I assume its 120V already: so, yes, you'll have to wire for a 240V receptacle (240V uses 1 more current carrying wire than 120V). Even if there were enough wires at 120V you'd still need a larger size wire for the combo unit. An electric dryer is a beast with electrical current.
just leave the neutral wire as it is and connect the other two !!
Ground wire not secured at the GFCI outlet or disconnected at another outlet feeding power to the GFCI outlet.
how do you hook up an outlet to a pull chain light without the outlet shutting off when you pull string
Turn off the supply to that outlet and check if any other outlet is also without power. this can be done by many methods.
No a cigarette lighter outlet can not be installed on a snow machine without a battery. The outlet will have no way to charge up.
Try to find another outlet for this narcissist.
There is a Bose outlet store in Nashville at Opry Mills Mall, and another in Sevierville/Pigeon Forge.
If you need to ask, you should have someone who knows how do it....
It's possible that the outlet is on a switch, and either one half of the outlet is switched or the whole thing. The extra two pair of wires probably feed the NEXT outlet.
Use jumper wires to go from one outlet to the other.
Without a proper converter, no you can not. The consequences would be damage to the equipment, wireing, fire, and possible injury or death. Don't do it. Have a single phase outlet installed.
tamper proof means that the device cannot be accessed without the use of a specialist tool .
If you can plug the fridge into another outlet and it comes on, then the issue is either a bad outlet connection or the circut breaker may be going out and needs replacement. Try the fridge on another outlet 1st. If it trips that one too then there is a short in your fridge.
It is plugged into an electrical outlet without a transformer
Some rooms have an outlet controlled by a light switch at the door. This is normally in bedrooms. It is possible that the switch is wired to only one of two outlets in a duplex outlet since it is easy to configure a duplex outlet to separate the bottom and top outlets.
There are several possible causes for an electric outlet not working:The outlet has gone bad such as internal contacts corroded or bent so they don't make a connection.The wire on the outlet is not connect or loose, not connected properlyThere is a break in the wire somewhereNo power going to the outlet from the source, which could also be caused by a bad fuse
Not without moving up two wire sizes from a #14 copper wire rated for 15 amps to a #10 copper wire rated for 30 amps.
Yes provided it is installed to code. You also might want to mark it in some way unless the plug is of a different configuration than the standard outlet.
There are several possible causes:The outlet has gone bad such as internal contacts corroded or bent so they don't make a connection.The wire on the outlet is not connect or loose, not connected properlyThere is a break in the wire somewhereNo power going to the outlet from the source, which could also be caused by a bad fuse
Yes, plug it into an AC wall outlet.
no it is not possible. mark tahiliani
The tag Heuer outlet has many pieces of jewelry for sale. They have almost the quality of retail stores but that are not of the latest as they didn't get sold.
Basically you need to connect the black supply wire directly to the outlet rather than have it go through switch. You can have two possible conditions. The first condition is that the supply comes to the switch box and connects to one side of the switch. The other side of the switch goes to the outlet. In this case just remove each black wire from the switch and connect them together with a wirenut. If the black supply wire goes to the outlet and there is another black wire going to the switch then there will also be a wire coming back from the switch. Just disconnect the wire coming from the switch to the outlet and connect the black supply wire directly to the outlet.
Should be a 240 V. 30A. 4 slot dryer recep. Should be fed with 4 #10 Cu. wires from the panel. Two hot wires are landed on a 2P30A circuit breaker, the White wire is landed on the Neutral bus bar, the Ground (Green) wire is landed on the Ground bus bar.