answersLogoWhite
Toyota Corolla

Is there a sensor or fuse for a 1989 Toyota Corolla radiator fan?

525354

Top Answer
User Avatar
Wiki User
2015-07-17 17:50:13
2015-07-17 17:50:13

IY IS A FUSE, NOT A SENSOR. THERE ARE 3 FUSE BLOCKS, ONE IS IN THE ENGINE COMPARTMENT ON THE DRIVERS SIDE WHEEL WELL AND THE OTHER TWO ON THE RIGHT AND LEFT SIDE KICK PANELS UNDER THE INSTRUMENT PANEL, YOUR FUSE PANEL SHOULD BE LABELED BUT IF NOT CHECK ALL YOUR FUSES. JUST MAKE SURE TO REPLACE ANY BAD FUSES WITH THE CORRECT AMP FUSE.

ANSWERTHERE IS A SENSOR LOCATED ON THE THERMOSTATT HOUSING. IT CAN GO BAD, RESULT WILL BE FAN WON'T GO ON OR WON'T STAY ON, CAR WILL OVERHEAT IN STOP AND GO TRAFFIC

The fuse is located in the fuse box in the passenger compartment, drivers side, to the left of where your left foot is (when sitting in drivers seat). The fuse and relay box under the hood behind the battery that is rectangular in shape and is the large of the two black boxes contains "fan relay 1" which is for the radiator cooling fan. If there are other relays in that same box that have the same part numbers listed, you can swap them out to see if the relay is bad.

1

Related Questions

User Avatar

what is the firing order for a corolla 1984? The firing order for Toyota Corolla from 1984 to 1989 is 1,3,4,2.

User Avatar

TROUBLESHOTING FOR REPLACED STARTER IN TOYOTA COROLLA 1999.

User Avatar

The 1989 Toyota Corolla Weygand rear speakers can be found in the side compartments of the rear of the vehicle. There will be a speaker on each side.

User Avatar

The recommended tire size for the 1989 Toyota Corolla is 175 R70 13. However, a size larger can be used with no harm to the car.

User Avatar

I am now able to answer my own question for anyone else who may be interested. It is located near the engine by the lower radiator hose.

User Avatar

I want to know the wiring color codes of the Toyota corolla 2006 car radio.

User Avatar

When owning a car it is important to maintain the fluid levels. A 1989 Toyota Corolla uses 1 quart of Universal ATF transmission fluid.

User Avatar

The 1989 Toyota Corolla tail light relay switch can be found in the fuse box. The tail light relay switch will be in the third column, second from the top.

User Avatar

The 1989 Toyota Corolla serpentine belt can be tightened or loosen with the tensioner pulley. Pry to the left on the tensioner pulley until the belt is tight. Tighten the tensioner pulley.

User Avatar

It looks like a bolt with a wire coming out of it on the side of the engine block, usually on the same side as the oil filter

User Avatar

Toyota corolla ignition coil can be found inside the distributor assembly together with igniter circuit... engine is 16valve carburator type..

User Avatar

Remove the tire and wheel from your 1989 Toyota Corolla. Remove the end of the axle. Remove the axle seal. Remove the wheel bearing. Reverse the process to install your new wheel bearing.

User Avatar

There are three coolant sensors installed to a 1989 Toyota Corolla 1.6 GL. One is a thermostatic valve switch that controls vacuum lines and is located near the passenger side of the carburetor and below the intake manifold. This can be identified by the hoses connected to it. The two other coolant sensors are located immediately before the big water hose leading to the radiator (upper hose). These two sensors can be identified by their electrical connectors. The bigger terminal is connected to a relay that controls the operation of the radiator fan. The smaller terminal is connected to the temperature gauge at the instrument panel.

User Avatar

on most Japanese cars the horn is up behind the front bumper its a flat disc about an inch deep maybe lessAnswerIn-between the bumper and the radiator on the left side.

User Avatar

Check the brake light switch located under the 1989 Toyota Corolla. If the switch is stuck the parking light will continue to stay on.

User Avatar

Probably at the engine end of the upper radiator hose

User Avatar

Replacing a starter on a 1989 Toyota Corolla is not very difficult to do. The wires will need to be disconnected from the old starter and labeled or taped. The starter is held in place by two bolts, unscrew the bolts and remove the old starter. Then replace with the new starter.

User Avatar

by your clutch pedal but far left attached to your inere wheel well

User Avatar

My Toyota corola 1.6gl 1989mod 16valve, lost the idling. wat can i do to fix it?

User Avatar

When changing belts, it is important to know the layout and have a diagram to help guide the removal and replacement of these belts. A diagram for these belts can be found in the maintenance manual of a 1989 Toyota Corolla 4-A-F.


Copyright © 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.