Oldsmobile Intrigue
Synonyms and Antonyms

Is there another name for the servo motor on a 1999 Oldsmobile Intrigue?


Top Answer
User Avatar
Wiki User
2006-08-02 12:14:14
2006-08-02 12:14:14

"Thing-a-ma-jig". Actually, I don't know of any other servos but the two for the climate control. An old-timer may call them "dash pots".


Related Questions

The servo motor is a type of motor which acts according to the command of the user. which serves the purpose of the user. therefore it is called as "servo" motor

A stepper motor will increment rotation in responding to control signals. a servo motor on the other hand will move to a signal input to stabilize the servo loop

No, stepper and servo motor are by mechanical design two different types of motors.

A hydraulic piston is also known as a servo or a motor.

A servo motor is one which is coupled to a sensor to achieve precise control of position, either linear or angular.

Servo motors are used for precision motion control application.

A modified servo motor allowed to spin around with an unlimited range.

Before looking for the servo check your vaccum line from the back of the engine it goes across the firewall down the passenger side-inside fenderwell, then und&er the battery and back to the lower firewall. Lots of Intrigues battery aicid eat this little black line into around the battery box. This creates no vaccum to the heat & air door controls.

A servo motor is an electric motor with a built in rotation sensor, they are needed for robotics. Say a robot moves its arm by turning a servo motor, the motor would send information concerning the degree of rotation on its axis back to the robot so the robot can keep tabs on the position of its arm, so if something bumps its arm it will know it and so-on.

That's a potentiometer with a servo motor attached for making the adjustments via electronic control.

A "servo motor" and a "servo" are the same thing. Servos are constructed from three basic pieces; a motor, a potentiometer (variable resister) that is connected to the output shaft, and a control board. The potentiometer allows the control circuitry to monitor the current angle of the servo motor. The motor, through a series of gears, turns the output shaft and the potentiometer simultaneously. The potentiometer is fed into the servo control circuit and when the control circuit detects that the position is correct, it stops the motor. If the control circuit detects that the angle is not correct, it will turn the motor the correct direction until the angle is correct. Normally a servo is used to control an angular motion of between 0 and 180 degrees. It is not mechanically capable (unless modified) of turning any farther due to the mechanical stop build on to the main output gear.

Try to reset dual climate HVAC door servo by disconnecting battery for 5 minutes mininum, then reconnect. If this doesn't work, servo has fallen out of range and needs to be replaced. This was happening to my 99 olds. Intrigue. Took it in, and it had a broken valve they replaced it and recharged the freon and it works great.

A servo motor rotates very accurately to the user's direction with a joystick and other controller while a induction motor spins when it is given power.

It depends. Servo Motor provides a smoother flow rate than a stepper motor, but most companies manufacture syringe pumps with a stepper motor due to number of stopping point and exactness of stopping. This provides aspiration and dispense accuracy and precision. Syringe Pump with Servo Motor (such as PSD/3) however provides smooth flow rate and flow rate accuracy.

servo motor is basically a very sensitive motor which is generally used in CNC,& NC machine tools . the main function of it is to guide the tool during the machining process as per pre set/ fed programme.

A servo motor uses position and/or velocity feedback to control its position and/or velocity. A stepper motor, on the other hand, uses magnetic detents to allow positioning to known positions based on pulses received from the driver.

A motor that controls the action of the mechanical device in a servomechanism.

it controls the over pressure of the water

A servo motor is a motor for which the rotor's position must be known, although it may be required to run, for example, exactly ten revolutions. A stepper motor is controlled by effectively DC signals (although these may be switched so fast that DC is an inappropriate term) so that it will always move from one exact position to another, through a known angle of no more than, say, 120 degrees.

yes servo motor are use latest technology in the field.

in servo stabilizer voltage deviation is less(nearly+-1),in stabilizer it is +-10.The reason is in stabilizer there is only 3 or 4 out put based on input,but servo stabilizer works with servo motor therefor it will vary the out put with input through its movement over the transformer coils ,out put is taking from the contact portion of the servo motor with the generator stabilizer out put is taking from some intervals .

That is a lubricant, specially an oil for motor vehicles

the sprrd regulation is cnsiderably improved.

servo motors change their rpm as instructed servo motors recieve instructions from a controller to do some action servo motors generally have feedback so the controller can see where they need to go servo motors can be electric air or hydrolic powered an example: cars have a cruse control you set a desired speed of travel the vacuum powered servo motor controls the throttle of the gas engine the transmission controls the ratio of gearing so the engine is not overloaded at some point when conditions are satisified you will get the correct speed ... if you go over the desired speed the vacuum powered servo motor backs off which eventually controls the differential driving rpm of the rear wheels here again the servo motor can be considered to be the valve on the vacuum bladder or the entire drive train

Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.