Disclaimer: The light is reminding you to change your oil.
1. Press "Power" with the brake pedal applied in the same way you would normally start your car.
2. Press the "Odo/Trip" button such that the regular odometer reading is showing rather than one of the two trip odometers.
3. Press "Power" again to turn off the vehicle.
4. Hold down the "Odo/Trip" button, hold down the break pedal and then press "Power".
5. Keep holding the "Odo/Trip" button for three or so seconds and then release the button.
That's it! Just make sure to change your oil.
This doesn't work for a 2010 Prius. Here how to do it for a 2010 Prius:
1) With the power on, switch to the odometer/trip-meter to display "TRIPA".
2) Power OFF (push the "Power" button).
3) Power ON, while holding the button for toggling between "km/h" and "MPH"
4) You will get a screen showing the reset of the oil change data.
5) When the reset is complete, release the button.
How to Reset Maintenance Warning Light on a 2008 Toyota 4Runner
To reset the engine light on a Toyota Prius, disconnect the negative battery cable and let off for about five minutes, then reconnect it. The light should go off after the first couple start ups.
A maintenance light on a Toyota Camry can be reset by your mechanic after you have the work done that is needed. You also may be able to get instructions by checking your manual.
How do you reset maint read light on 2010 corolla
maintenance with engine
Resetting the maintenance light on a 1999 Toyota Tacoma is very easy to do. To reset the light, take the battery cables off for up to one minute to reset the light.
How do you reset the maintenance required light in the 2011Toyota RAV4 with a smart key starting system
disconnect the battery
how to reset maintenance light on mercedes s550 amg
Your drivers manual should give you the information to reset the oil maintenance light.
Set it to trip A and hold reset turn ignition off then turn ignition on and maintenance light will flash and your done.
You will need to take it into a mechanic. They will be able to check out your vehicle and then they can turn off the light.
How do you reset maintenance reminder light on 2008 Toyota corolla? For what it is worth: To reset the Maintenance Required light on my 2007 Toyota Corolla: 1) Set your trip meter to the odometer setting (in other words, not Trip A or Trip B) 2) Hold down trip meter reset button and turn ignition to off. 3) While holding down the trip meter reset button now turn the ignition to on. 4) Keep holding down button until Maintenance Required light shuts off. Note: One some other Toyota models you hold down the Trip A meter rather than the odometer. Hope this works for you.
After repairing the cause of the code, you reset with a scan tool.
With the ignition switch in the off position, hold in the hold in the trip odometer. Now turn on your key and you will see a series of zeros begin to appear. Once that stops, your maintenance light will be reset.
A person can reset the maintenance required light on a 2004 Toyota Sienna by holding down the odometer trip button. A series of zeroes will appear, which indicates that the light has been reset.
how do you reset the check engine light on a 2005 Toyota tundra
Your owners manual should tell you how to reset the light.
To reset the T belt light in Toyota kindly see your manual or take it to a Toyota accredited car dealer.
To reset a 2007 Toyota Rav4, the steps are as follow:= = 1. Move odometer to Trip A then hold down. 2. Turn off ignition then turn on to ACC. (Don't turn on engine). 3. The reset will go through 000000.00 then _ _ _ _ _ going to ---- going to --- etc. 4. Once it runs through the reset, the maintenance required light flashes and goes off. 5. Easy fix, not sure why Toyota doesn't have this in the manual.
How do you reset the Airbag warning light on a 1995 Toyota Avalon?
same as a 2005 odometer OS on turn key off hold reset turn key on loght flashes then turn off
Check engine light or required maintenance light. Procedure for resetting required maintenance light just answered. Check engine light requires an OBD II to determine problem and turn the light off.
Set the odometer reading to total miles and not to trip miles. Now press and hold the odometer reset button in and turn the ignition switch to the on position. (Do not start the engine). After around 5 seconds of holding the reset button in the maintenance required light will go off and be reset. Release the button and turn the ignition off.
The maintenance light,You will need to take it to a Dodge dealer to reset it. Or get a DBR-2 code scanner.BIG $$$