answersLogoWhite

0

  • Dodge Intrepid
  • Ford Explorer Eddie Bauer
  • US Army

On a 1994 Dodge Intrepid why won't your car crank up even if it turning over but not firing up?

User Avatar

Wiki User

βˆ™ 2008-05-18 16:28:27

Best Answer
Copy

my 95 intrepid is doing the same thing check the "engine controller" fuse under the hood i do this but it blows out every so often still trying to figure that out

User Avatar

Wiki User

βˆ™ 2008-05-18 16:28:27
This answer is:
πŸ€“
🀯
πŸ€”
User Avatar

Your Answer

Loading...

Related Questions

Where is the crank sensor on a 1993 Dodge Intrepid?

where is the crankshaft sensor located on a 1993 dodge intrepid


1999 Dodge Intrepid just shut off it will crank but not start?

what do i do


1999 Dodge Intrepid heater is not working very well?

1999 dodge intrepid is not starting I change crank and camshaft sensor and it stall will not start what can i do next.


Where is the water pump located on a 2001 Dodge Intrepid 3.2?

Behind the crank case cover.


Where is crank sensor on 1996 Dodge Intrepid?

On the passenger side bell housing on the near the transmission.


How do you get the timing gear off the crank on a 2002 Dodge Intrepid 2.7 motor?

With a special puller.


Why 96 Dodge Caravan is not firing?

crank sencer, coil pack, or ecm


How do you test a crank position sensor on a 2000 Dodge Intrepid?

scanning for codes will indicate if the CPS is at fault.


What is the pulley for your timing belt directly behind the crank shaft called on a 1997 Dodge Intrepid 3.5L V6?

Timing belt crank sprocket


Will not crank no fire codes OK coil OK 96 Dodge Intrepid 3.5 what to mlook for?

try crank position sensor and cam shaft sensor


How do you remove crank sensor on a 2000 Dodge Intrepid?

Disconnect the electrical connector, remove the mounting screw and remove the sensor.


Where is the crank sensor on a 1996 Dodge Intrepid?

It is mounted to the passenger side of the transmission bell housing, just behind the engine.


How do you change a crank sensor for a 1994 Dodge Intrepid with 33 motor?

It is located on top of the transmission next to where is mounts up with the motor


How can you tell if the crank shaft pulley is broke in a 2000 Dodge Intrepid 2.7 liter 6v engine?

Take It Off Amd Inspect It.


Where is the crank sensor and how much does it cost?

how much cost a crank sensor for a intrepid 1999


Will 3.3L intrepid run with crank sensor unpluged?

No


Replacing timing chain and need firing order for 1997 Dodge Intrepid 3.5?

123456 That should have been marked on the intake manifold, towards the rear of the engine. The firing order is correct! However, it has a timing belt, not a chain. The water pump is driven by the timing belt, so replace that while your in there. And Make sure the crank and cams on on TDC before you put the belt on!


Where is the crankshaft sensor on a 1994 Dodge Intrepid with a 3.3L engine?

the crank sensor is on the passenger side of the car on the back of the engine. Check right up there by the transmission housing.


1996 Dodge Intrepid stalls when i am coming to a stop and i try and take off.changed fuel filterstill stalls?

Try the crank sensor first, then the cam sensor. without these the car will not spark. Most commonly the crank sensor though.


Does the 94 dodge ram 318 magnum have adjustable timing Is it done by turning distributor?

It is zeroed to the crank with a scan tool. It can not be done with a timing light. It is done by turning the distributor.


What tools can you use to pull out a crank shaft pulley for a Dodge Intrepid 2002?

3 JAW PULLER. (You can buy it at any autozone, CAP or NAPA) $10.00 - $20.00 bucks.


Where is the crank sensor located on a 1995 Dodge Intrepid with a 3.5L?

on the right front of the transmission bell housing about 3 o'clock. If you are looking at the engine it will be on the left. There is 1 10mm bolt holding it down.


Why will your 98 intrepid turn over but not fire?

try replacing crank sensor


How do you remove the crank pulley on a '96 Dodge Intrepid 3.5L to change the timing belt?

You'll need a puller you should be ablt to get a lon from on of you autoparts suppliers without this you will not be able to remove it Jim.


Is the ignition timing for a 2001 dodge ram 5.9 magnum controlled by the ecu or by turning the distributor?

It is controlled by the computer. The distributor needs to be synced to the crank sensor.