answersLogoWhite

0


Best Answer

First take off the door panel. Check for the proper voltage at the motor connector when the switch is in the on position. If you have no voltage then it might be the switch assembly. If you have voltage and the window doesn't move you may have to replace the motor. This is difficult but can be done if you are patient. Disconnect the power to the motor. Drill out the three rivets and detach the motor from the regulator. Reverse the procedure to replace the motor. Short bolts and nuts can replace the rivets but due to clearance the rivets are the best. You may have to rent a large rivet gun.

User Avatar

Wiki User

โˆ™ 2006-03-31 00:32:26
This answer is:
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
User Avatar
Study guides
๐Ÿ““
See all Study Guides
โœ๏ธ
Create a Study Guide

Add your answer:

Earn +20 pts
Q: Rear rt hand power window does not go up on 1992 town car how do you repair it?
Write your answer...
Submit
Related questions

96 Trooper how do you repair the electronic window rear passenger?

96 Trooper how do you repair the electronic window rear passenger?


How do you repair rear window in Skoda octavia?

window heater not working


Rear Window Glass Repair?

Side and Rear Glass repair We also offer a complete side and rear glass replacement and repair service. All you need to do is tell us over the phone which panel of glass is damaged, and we can organize the repair immediately. The side glass is described as if you were sitting in the car, so Continue reading Side and Rear Glass repair


How do I repair 2003 Buick Lesabre rear left passenger power window lift mechanism?

go to flickr, I have several pictures on how to fix.


How do you fix the rear power window on Acura MDX?

how do i fix the rear passenger window of my acura mdx


Will the rear window of a 1992 explorer fit a 1999 explorer?

No.


How do you fix the rear power window on a 99 Saab 9-3?

To fix a rear power window on a 1999 Saab, the door panel will have to be removed to gain access to the power window motor. If the window is not working properly, it is either the motor or the cable.


How do you fix the envoy xuv rear power window?

What's the problem with the window?


How do you know if a power window is heated?

The only window that is heated in any car is the rear window. As far as I know ther's no such thing as a power heated window


How do you reset the left rear door power window on a Lexus LX470?

Reset the left rear door power window by removing the power window motor and connect both the motor and the power window switch to the vehicle's wire harness. Turn the ignition switch on and it should be able to reset.


How do you repair a rear window defogger for a 1992 Volvo 940 gle?

Replace the rear glass if you have determined all else in the system is working. The element wires are sandwiched between the inner and outer glass and are not serviceable of anything but the 240 series.


Will a 1992 Dodge Dakota rear window fit in a 1998 Dodge Dakota?

No


What is a rear screen relay?

You need to include more details. Normally it would be an electromechanical relay that controls the power and the direction of a vehicle rear door power window motor. The motor that raises and lowers the rear window in a vehicle that has a tail-gate, hatch or rear door window, like a Jeep Cherokee, or what we used to call a "station wagon." It could also be the electromechanical relay that controls the power to a vehicle rear window defogger/ defroster grid.


Where is the power safety switch for the 525i BMW 1992?

what is a power safety switch? The battery is under the back seat, and the ground wire can be unbolted from an access port in the front. If you refer to the power window safety switch, it is in between the two rear window switches and only affects them. There is no power lock safety switch.


How do you replace a rear glass window motor in a 2001 sport trac?

Removal and Installation NOTE: The power rear window motor can be removed and a new one installed without removing the seat or trim panel. NOTE: When the power rear window motor is removed and installed, the motor must be initialized. For additional information, refer to Rear Window Motor Initialization in this section. # Fold down the passenger rear seat back. # Open the luggage compartment trim panel access door.# Remove the spare tire jack and handle assembly.# NOTE: The rear window glass water shield uses a reusable butyl rubber adhesive. A new water shield does not have to be installed unless it is damaged or if the butyl rubber adhesive does not adhere to a section of the sheet metal. Position the carpet aside and position the water shield back from the rear window glass motor to access bolts.# CAUTION: Use care not to damage the drum housing when removing the rear window glass motor. NOTE: Apply pressure to the drum while removing the rear window motor to avoid extraction of the drum with the motor. Remove the rear window motor. ## Disconnect the electrical connector. ## Remove the bolts. ## Remove the rear window glass motor.# NOTE: The rear window motor must be initialized after a repair is carried out. For additional information, refer to Rear Window Motor Initialization in this section. To install, reverse the removal procedure. (PASTED IN BELOW) == CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure. NOTE: The rear window motor is in error mode when shipped and will be inoperative until initialized. NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window glass module is installed, and any operation in which grease or lubricants are applied to the power rear window system. NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure. NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed. NOTE: Step 7 requires that the power rear window control switch be held in the CLOSE position (fully clockwise) until the power rear window motor stalls the window into the upper header seal. Step 8 requires that the window control switch be momentarily turned to the OPEN position. NOTE: Step 9 requires that the power rear window control switch be held in the CLOSE position (fully clockwise) until the window stalls into the upper header seal and the window carries out its down-up sequence, indicating successful completion of initialization. NOTE: The key-in-ignition chime can cause the vent button to be pressed more or less than six times due to the distraction of the chime. # NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes. Start with the ignition in the OFF position. Open the driver door.# Turn the ignition to the ON position. # Press the power rear window control switch vent button six times.# Turn the ignition to the OFF position. The driver door must be OPEN. # Press the power rear window control switch vent button six times.# Turn the ignition to the ON position. The power rear window will move down-up-down-up approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialization mode. # Rotate and hold the power rear window control switch to the CLOSE position until the window stalls into the upper header seal.# Momentarily rotate the power rear window control switch to the OPEN position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.# Rotate and hold the power rear window control switch to the CLOSE position. Continue to hold the switch until after the window stalls into the upper header seal and carries out the down-up movement. This down-up movement is approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.# Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions. If the window does not operate correctly, carefully repeat this procedure.


Location of Power rear window motor 2006 Ford F150?

behind rear seat


How many lines can you repair on rear window heater on a 1991 volkswagen golf?

as many as you have, as many as you have,


How do you repair power window switches on drivers side Lincoln Continental 2002 can only open drivers side and right rear from drivers control left rear and passenger will not work from driver?

Replace driver's switch assembly


How do you repair the rear window defroster on a 1999 Ford Mustang?

Relace the rear window.....the heating coils are imbedded into the glass....or check the connections and trace the wire,check the fuses before you go that route.


How do you repair a rear window heating element?

Depends on the nature of the problem. If the grid lines are broken you can get a repair kit that you basically paint on after you mask it off with tape.


How do you initialize the rear window motor on a 2001 ford sport trac?

Rear Window Motor InitializationWhen you install the new motor, it MUST BE "INITIALIZED" before it will function properly. Simply follow the instructions below. CAUTION: Make sure that no obstructions are present in the power rear window system when carrying out this procedure.NOTE: The rear window motor is in error mode when shipped and will be inoperative until initialized.NOTE: This procedure must be carried out when repairs are performed on any part of the power rear window system including when: the power rear window motor is removed from the window regulator drum housing, a new power rear motor is installed, a new power rear window regulator is installed, a new power rear window glass module is installed, and any operation in which grease or lubricants are applied to the power rear window system.NOTE: All power rear window components (window glass module, window regulator, window motor, and glass runs) must be installed and torqued to specification before carrying out this procedure.NOTE: Once the ignition key is turned to the ON position in Step 6, it must remain on until the entire procedure is completed.NOTE: Step 7 requires that the power rear window control switch be held in the CLOSE position (fully clockwise) until the power rear window motor stalls the window into the upper header seal. Step 8 requires that the window control switch be momentarily turned to the OPEN position.NOTE: Step 9 requires that the power rear window control switch be held in the CLOSE position (fully clockwise) until the window stalls into the upper header seal and the window carries out its down-up sequence, indicating successful completion of initialization.NOTE: The key-in-ignition chime can cause the vent button to be pressed more or less than six times due to the distraction of the chime.NOTE: Steps 1-6 must be completed within 30 seconds. The entire procedure must be completed within five minutes.Start with the ignition in the OFF position. Open the driver door.Turn the ignition to the ON position.Press the power rear window control switch vent button six times.Turn the ignition to the OFF position. The driver door must be OPEN.Press the power rear window control switch vent button six times.Turn the ignition to the ON position. The power rear window will move down-up-down-up approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has entered initialization mode.Rotate and hold the power rear window control switch to the CLOSE position until the window stalls into the upper header seal.Momentarily rotate the power rear window control switch to the OPEN position and release. The power rear window will carry out a one-touch down operation until the window stalls at the bottom of the travel stop designed into the window regulator.Rotate and hold the power rear window control switch to the CLOSE position. Continue to hold the switch until after the window stalls into the upper header seal and carries out the down-up movement. This down-up movement is approximately 20 mm (0.8 in). This movement indicates that the power rear window motor has been successfully initialized.Verify correct operation of the power rear window by moving the window to the fully open, vent, then fully closed positions. If the window does not operate correctly, carefully repeat this procedure.NOTE. You will need to close the door after step 6.


How do you repair a rear automatic window on a 2000 Audi A4. You can hear the motor running when you push the button to put the window up but the window won't move?

The regulator is shot. Replace the regulator.


How do you repair a rear left electric window in a 1998 Lincoln town car?

Yes it does have rotor for front and back, with the emergency brakes inside the rear rotors.


How do you repair the rear window defogger element on a 2005 Jeep Liberty?

I would go to a professional mechanic to have him/her fix it. Your issue could be an assortment of things; it could be the element in the rear window, wiring, or circuitry.


How do you replace a front power window motor on 2002 Ford Explorer?

How do you replace a power window motor ( rear passenger side ) in a 2002 Ford Explorer