How do I removed the oil pan on a 1996 Honda accord lx 2.2L auto
trans 4 cylinders?
On the bottom of the transmission.
On a 1996 Accord, the blower motor is located in the dash behind the glovebox. The door to the glovebox must be removed and the frame needs to be taken out of the dash to get to the blower motor.
radiator hose needs replacing. use and heat will cause hose to collapse when worn out
yea they should. They change in 97
Inside the evaporator case which is behind the glovebox
if factory wal mart sells wire harness and it does some after market serios
Failure in emission system - have vehicle scanned to determine problem
It mostly depends upon the motor that is in your vehicle and the motor in the vehicle in which you are removing the transmission from. It should work as long as they are removed from the same motors. The transmission on a 4cyl will not bolt to a 6cyl. www.FordRanger.net
(kg) 1,458, curb weight
controlled by computer --not adjustable
there should be a rear sway bar
The automatic is called a 46re. The manual is a nv4500.
where is located on a 1996 jaguar xj6 starter ?
why does oil come out of dipstick on a1996 12v commin
Most Chevy v8's are 18436572.
NO. The bellhousing is different on the 1996 model only.
No. This is a completely different transmission.
Its located in the right(driver) side under the exhaust manifold....
wher are the oxyegen sesors located on a1996 ford contour
My 93 is behind passenger side kick panel.
It will give you the code when the battery has been disconnected.
The fuel capacity of 1996 Mercedes e320 is 80 litres.
One from another Nissan Navara D21
6 qts if your asking for doing an oil and filter change
what is the unladen weight of a ford escort 1.8 D van
It's still worth $2 Canadian.
I would doubt you would pour engine block sealer into coolant. More likely it would just need to be put in with the oil. Like lucas. I dont know your particular product. Depends also, are you leaking coolant, or burning it?
its located on exhaust manifold looks like a spark plug with awire on it.
Should be listed on the oil cap and in your owner's manual. I think you will find it is 5w30.
The are two letters just above the words Exterior Paint on the label on the driver's door.
Usually stamped on the bottom frame rail behind the front left wheel.
what is the plug wire placement on the distributor cap of a1996 gmc 4.3 v6?
It is mounted on the drivers side of the frame underneith the car back towards the rear end.
If it is a automatic transmission then it will be a 4L80E. Sorry but I don't remember what kind of stright stick transmission it had.
Trouble code P0731 means: A/T Additional Gear Ratio Error In First Gear
On a1996 Buick Le-sabra it is on the Driver side under hood right below brake fluid reservoir.
Motorcraft MERCON automatic transmission fluid - according to the 1996 Ford Ranger owners manual
I believe that the both the 96 vette and caprice use the LT1 (I think 96 was the last year for the LT1). In that case, yes.
.054 inch ( according to fordparts.com ) - check the information sticker under your hood for the spark plug gap
YES, they are both TBI. You will need to keep everything else with the original truck due to computer issues.
Probably a faulty blend door actuator. Remove the glove box to gain access to the actuator. Replace the actuator with a new one.
well if its not overheating then they should not be on if it is overheating and they dont come on you need to check the control temp switch for them should be on top of the head somewhere
Click on the link below Click on Owner Guides The owners manual ( which includes the fuse diagram ) can be viewed online
Find it,unbolt it, pull it out, push in the new one, bolt it snug not tight or youll break the new one Or take it to a qualified mechanic
No, the 1988 uses a AW4 trans. The 1996 Grand uses a 42re trans.
Low coolant? Thermostat not opening? Water pump not circulating coolant? cooling fan not working? System air bound? Radiator plugged or restricted? Defective radiator cap?
yes you shouldent have any problems check the piston dish cc to be shure (see if they look the same)
Under the valve covers. Be very carful with the Valve cover gasket as they are also part of the wireing harness. Almost $100 each last time I checked.
If it's part of the computer controls it will almost ALWAYS show up when you do a computer diagnostic test. Borrow, rent or buy a code scanner for your Ford and see what it says.
find the data link connector under left side of dash. put jumper wire from pin 7 to pin 19 & turn key to run. do not start. count to 10 & pull jumper. should reset