Isuzu
Heater Cores and Blower Fans
Jeep Wrangler Sport
Chevy Blazer S-10

Resistor block for blower motor 96 Isuzu?

585960

Top Answer
User Avatar
Wiki User
2011-09-13 13:31:18
2011-09-13 13:31:18

Blower Resistor block for the heater/ac motor on my 1996 TROOPER, is located on the heater/ac unit in the cab, passenger side. Remove the glove box,(2 screws on the bottom hinges, then open the box and it will lift out) You will see an opening on the left side with a wire harness of 5 wires. Unplug the harness, and remove the 2 Phillips screws and the resistor block can now be removed! About 10 minites total labor to do it youeslf. Beats being charged a couple hundred bucks to the dealer for parts and labor. Part is about $55.00 retailer from the dealership, check online and you should be able to order it from a discount parts supplier. From what I've found online, when the heater/ac blower quits, it is usually the restistor block about 90% of the time. Regards, Gary

1
๐Ÿ™
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0

Related Questions

User Avatar

The resistor block or blower motor resistor is used to control the speed of the blower motor. That is how you get the lower speeds on your air conditioning or heater. The higher the resistance the lower the speed of the motor.

User Avatar

Pull out the lock on the blower motor resistor wire harness connector to unlock the connector latch . Depress the latch on the blower motor resistor wire harness connector and disconnect the connector from the resistor. Remove the two screws that secure the blower motor resistor block to the HVAC housing. Remove the resistor block from the HVAC housing............

User Avatar

To test the blower motor resistor, unplug the resistor connector. Each blower motor switch input terminal on the resistor must have continuity to the resistor output terminal, which is connected to the circuit going to the blower motor. If the blower motor resistor continuity does not check OK, replace the faulty resistor.You need a multimeter to test the resistor block and there should be continuity between all terminals.

User Avatar

A malfunctioning blower motor resistor will cause the blower motor not to work. When the resistor is bad the blower motors will not turn on.

User Avatar

this resistor is located next to the blower motor in the heater plenum. the coils sit in the air stream. remove the connector and the fasteners and pull the resistor block out.

User Avatar

The a/c heater blower motor resister is located in the vehicle on the passengers side inside the housing next to the blower motor...............Remove the blower motor resistor wire harness connector.Remove the blower motor resistor screws.Remove the blower motor resistor.

User Avatar

Generally the blower motor resistor is found close to the blower motor. It relies on the blower motor to keep it cool.

User Avatar

The blower motor is located in the same area as the resistor, it's held in with 3 screws. Removing them will allow the motor and wheel to drop down.

User Avatar

Fig 15 Blower Motor ResistorNOTE: The blower motor resistor is located on the lower right side of the heater housing.REMOVAL# Remove lower right underpanel silencer/duct. # Disconnect wiring connectors on blower motor resistor. # Remove blower motor resistor retaining screws. # Pull blower motor resistor out of heater housing.

User Avatar

The blower motor resistor has failed.The blower motor resistor has failed.

User Avatar

99% of the time, the blower motor relay, or resistor block,will be bad if the fan motor only works on high speed.

User Avatar

The blower motor resistor block is located on the underside of the HVAC housing (Heater Box) next to the blower motor. The blower motor is located at the right side of the dashboard. You can access the blower motor resistor block from under the dashboard. A Word of Caution! Stay clear of the blower motor resistor block heat sink - It could be Hot. Incidentally, I have read about people working on their dashboards and setting off the airbag. It is a good thing to disconnect the negative battery cable from the battery and make sure that it can not touch the battery post. Wait at least a couple of minutes for the airbag system to discharge.

User Avatar

It's in the resistor block, which in the diagrams comes right after the fan control switch

User Avatar

The blower motor fan cools the resistor so the resistor is usually located close to the blower.

User Avatar

The 1991 Honda accord blower motor resistor is located on the firewall in the engine compartment. The blower motor resistor will be on the passenger side of the firewall.

User Avatar

In general, the blower motor resistor is located close to the blower motor.

User Avatar

where is the blower motor resistor in a 2003 Mitsubishi eclipse

User Avatar

The blower motor resister block is located in the center of the dash. Remove the complete glovebox and look to the left and you will see it...............

User Avatar

Behind the glove compartment on the dash.

User Avatar

Your truck has both. the resistor is between the switch & blower.thje resistor controls the blower speed

User Avatar

The Resistor is located on the outside of the blower motor. Have to remove the blower from under the glovebox to get to it. The Resistor is located on the outside of the blower motor. Have to remove the blower from under the glovebox to get to it.


Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.