Auto Parts and Repairs
Turn Signals and Hazard Lights

The turn signals and hazards lights do not work how do you fix this problem?

567

Top Answer
User Avatar
Wiki User
Answered
2009-04-14 21:51:28
2009-04-14 21:51:28

Could be the bulbs or the fuses or the flashers or the signal switch assembly

001
๐ŸŽƒ
0
๐Ÿคจ
0
๐Ÿ˜ฎ
0
๐Ÿ˜‚
0
User Avatar

Related Questions


Your problem is most likely the turn signal relay im having a problem similar to yours but when my signals wont work neither do my hazards


hazards and turn signals have separate flashers. replace flasher for turn signals



If the 4 Ways/Hazards are disconnected then neither will work the park lights nor the turn signals.


The problem that I had with my 2001 Ranger rebuild was I had tail-lights and back up lights along with brake lights. No turn signals or hazard lights. More than likely, it is a bad turn signal control arm. There is also a relay box under the dash. My problem was that the relay had gotten wet and had rusted inside. As soon as we replaced this, I had turn signals and hazards. Hope this gives you a reference where to start your search. Good Luck, Dan


It contains two relays, one for hazard lights and the other for turn signals. The one for the turn signals is defective and must be replaced.




Bad wiring i am guessing that something is wrong with your turn signal switch. Actually, The turn signals and hazard lights are controlled by 2 different relays. Try changing the Turn-signal relay.


No, they do not have traditional turn signals but have flashing lights.



Blown fuse or bad flasher unit. Often, cars use different flasher for the turn signals and the flasher, so it is possible for the hazards to work and not the turn signals.


It's probably time to replace your headlight switch. Had a similar problem on my '95. A new switch fixed her right up.


Your problem very well could be the hazard switch. i have a 1994 honda civic too i found whenever i disconnected the hazard switch from the wiring harness my turn signals brake lights and of course hazards do not work. Maybe replace the hazard switch..




If the turn signals on a car works but the hazard lights do not there may be a problem with the flasher switch. The flasher is located in the steering column, and a damaged unit can cause the lights to stop working.


If the turn signals are inoperative check the hazard switch, if the hazards don't work replace the hazard switch, the signals will start working. if the hazards are ok ,the turn signal switch may be bad.


The Flasher Relay is more than likely defective. Some vehicles have 2 relays. One for the turn signals and one for the hazard lights. Replace the Flasher Relay for the turn signals.



not sure what causes it, but sometimes my signals will just not work. with lever still in position to activate signal, push button for hazards. then put signal lever in "off" position. turn off hazards. signals should work. temporarily anyway.


this may be a relay problem just a guest but the turn signals and the hazards carry separate ts switch on most vehicle (not all)


probably have a bad relay, that was my problem.. Are your turn signals not working, but your hazards lights are? and if so, do you hear a constant clicking sound, like your turn signal is turned on? Does the clicking sound go away when you hit the brakes? It is the relay.


The only thing common to all those lights (but not to the center brake light) is the hazard switch. I'd check that next. On my 96 Century the hazards override the signals and brake lights meaning that the signals and brake lights must be wired into the hazard switch somehow.


I have a chev cavlier 1995 and the running lights do no work---on the dash the green light keeps blinking----what should I do?



Copyright ยฉ 2020 Multiply Media, LLC. All Rights Reserved. The material on this site can not be reproduced, distributed, transmitted, cached or otherwise used, except with prior written permission of Multiply.